121 lines
3.4 KiB
INI
121 lines
3.4 KiB
INI
# DO NOT EDIT THIS FILE, IT IS A TEMPLATE. THAT YOU NEED TO COPY
|
|
# Prusa MK3s Klipper Config
|
|
|
|
# The first thing you'll need to do is go through this file and comment out / uncomment
|
|
# the files and/or settings you need.
|
|
|
|
# You'll be able to print just fine with this config as it is, but it is recommended
|
|
# that you follow these steps to properly calibrate your printer:
|
|
|
|
# 0) Sanity check and PID Tuning: https://www.klipper3d.org/Config_checks.html
|
|
# 1) Pressure Advance: https://www.klipper3d.org/Pressure_Advance.html
|
|
# 2) Skew Correction: https://www.klipper3d.org/skew_correction.html
|
|
# 3) Resonance Compensation: https://www.klipper3d.org/Resonance_Compensation.html
|
|
|
|
# Read more about klipper here: https://www.klipper3d.org/Overview.html
|
|
|
|
### UI
|
|
# [include mainsail.cfg]
|
|
[include fluidd.cfg]
|
|
|
|
[mcu]
|
|
# serial: /dev/serial0 # If you are using internal RPI serial port
|
|
serial: /dev/ttyACM0 # If you are using RPI via USB connection to printer
|
|
restart_method: command
|
|
|
|
### CONTROL BOARD
|
|
[include klipper-prusa-mk3s/mk3s/einsy-rambo.cfg]
|
|
|
|
### BASE SETUP
|
|
[include klipper-prusa-mk3s/mk3s/display.cfg]
|
|
[include klipper-prusa-mk3s/mk3s/steppers.cfg]
|
|
[include klipper-prusa-mk3s/mk3s/tmc2130.cfg]
|
|
|
|
### EXTRUSION
|
|
|
|
# Extruder
|
|
[include klipper-prusa-mk3s/extruders/prusa.cfg]
|
|
# [include klipper-prusa-mk3s/extruders/bmg.cfg]
|
|
|
|
# Hotend
|
|
[include klipper-prusa-mk3s/hotends/v6.cfg]
|
|
# [include klipper-prusa-mk3s/hotends/dragon-standard-flow.cfg]
|
|
# [include klipper-prusa-mk3s/hotends/rapido.cfg]
|
|
|
|
[extruder]
|
|
# To tune Pressure Advance see https://www.klipper3d.org/Pressure_Advance.html
|
|
# default is already set based on hotend, but you can further improve prints by calibrating it to your nozzle and material
|
|
# pressure_advance: 0.05
|
|
nozzle_diameter: 0.4 # Remember to change this if you change nozzle diameter.
|
|
#pid_Kp: 23.862
|
|
#pid_Ki: 1.020
|
|
#pid_Kd: 139.595
|
|
|
|
## copy this from your current setting on Prusa, but make it absolute (removing -)
|
|
[probe]
|
|
z_offset = 0.685
|
|
|
|
## For faster printing enable
|
|
# [printer]
|
|
# max_accel: 2000
|
|
# max_accel_to_decel: 2000
|
|
# max_z_velocity: 20
|
|
# max_z_accel: 300
|
|
|
|
## For stealth mode enable
|
|
|
|
# [tmc2130 stepper_x]
|
|
# interpolate: True
|
|
# stealthchop_threshold: 80
|
|
# [tmc2130 stepper_y]
|
|
# interpolate: True
|
|
# stealthchop_threshold: 80
|
|
# [tmc2130 stepper_z]
|
|
# interpolate: True
|
|
# stealthchop_threshold: 80
|
|
|
|
## Custom bed mest probes
|
|
## Prusa has 3x3 or 7x7, you can do any variation you want
|
|
# [bed_mesh]
|
|
# probe_count: 4,4
|
|
|
|
# Linear correction
|
|
# Check `extruders/linear-correction` for more informations.
|
|
[include klipper-prusa-mk3s/extruders/linear-correction/linear-correction-0.cfg] # Default Prusa linear correction optimized for LDO motors
|
|
|
|
### MACROS
|
|
[include klipper-prusa-mk3s/macros.cfg]
|
|
|
|
# FIRST RUN:
|
|
# Execute these sequentially in the console, let PID tuning finish before saving
|
|
# PID_CALIBRATE HEATER=extruder TARGET=170
|
|
# SAVE_CONFIG
|
|
# PID_CALIBRATE HEATER=heater_bed TARGET=60
|
|
# SAVE_CONFIG
|
|
|
|
# You can also skip the above setting for stock Prusa and use
|
|
[extruder]
|
|
#control: pid
|
|
min_temp: 0
|
|
max_temp: 305
|
|
min_extrude_temp: 170
|
|
|
|
[stepper_z]
|
|
position_max: 210
|
|
|
|
[heater_bed]
|
|
pid_Kp=54.241
|
|
pid_Ki=0.646
|
|
pid_Kd=1139.053
|
|
|
|
### The end, on the end the printer will store it's tuning data, so do not edit it.
|
|
|
|
#*# <---------------------- SAVE_CONFIG ---------------------->
|
|
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
|
#*#
|
|
#*# [extruder]
|
|
#*# control = pid
|
|
#*# pid_kp = 25.678
|
|
#*# pid_ki = 1.297
|
|
#*# pid_kd = 127.106
|