initialise repo

printer-20240726_153750.cfg

@@ -0,0 +1,120 @@
+# DO NOT EDIT THIS FILE, IT IS A TEMPLATE. THAT YOU NEED TO COPY
+# Prusa MK3s Klipper Config
+
+# The first thing you'll need to do is go through this file and comment out / uncomment
+# the files and/or settings you need.
+
+# You'll be able to print just fine with this config as it is, but it is recommended
+# that you follow these steps to properly calibrate your printer:
+
+# 0) Sanity check and PID Tuning: https://www.klipper3d.org/Config_checks.html
+# 1) Pressure Advance: https://www.klipper3d.org/Pressure_Advance.html
+# 2) Skew Correction: https://www.klipper3d.org/skew_correction.html
+# 3) Resonance Compensation: https://www.klipper3d.org/Resonance_Compensation.html
+
+# Read more about klipper here: https://www.klipper3d.org/Overview.html
+
+### UI
+# [include mainsail.cfg]
+[include fluidd.cfg]
+
+[mcu]
+# serial: /dev/serial0 # If you are using internal RPI serial port
+serial: /dev/ttyACM0 # If you are using RPI via USB connection to printer
+restart_method: command
+
+### CONTROL BOARD
+[include klipper-prusa-mk3s/mk3s/einsy-rambo.cfg]
+
+### BASE SETUP
+[include klipper-prusa-mk3s/mk3s/display.cfg]
+[include klipper-prusa-mk3s/mk3s/steppers.cfg]
+[include klipper-prusa-mk3s/mk3s/tmc2130.cfg]
+
+### EXTRUSION
+
+# Extruder
+[include klipper-prusa-mk3s/extruders/prusa.cfg]
+# [include klipper-prusa-mk3s/extruders/bmg.cfg]
+
+# Hotend
+[include klipper-prusa-mk3s/hotends/v6.cfg]
+# [include klipper-prusa-mk3s/hotends/dragon-standard-flow.cfg]
+# [include klipper-prusa-mk3s/hotends/rapido.cfg]
+
+[extruder]
+# To tune Pressure Advance see https://www.klipper3d.org/Pressure_Advance.html
+# default is already set based on hotend, but you can further improve prints by calibrating it to your nozzle and material
+# pressure_advance: 0.05
+nozzle_diameter: 0.4 # Remember to change this if you change nozzle diameter.
+#pid_Kp: 23.862
+#pid_Ki: 1.020
+#pid_Kd: 139.595
+
+## copy this from your current setting on Prusa, but make it absolute (removing -)
+[probe]
+z_offset = 0.685
+
+## For faster printing enable
+# [printer]
+# max_accel: 2000
+# max_accel_to_decel: 2000
+# max_z_velocity: 20
+# max_z_accel: 300
+
+## For stealth mode enable
+
+# [tmc2130 stepper_x]
+# interpolate: True
+# stealthchop_threshold: 80
+# [tmc2130 stepper_y]
+# interpolate: True
+# stealthchop_threshold: 80
+# [tmc2130 stepper_z]
+# interpolate: True
+# stealthchop_threshold: 80
+
+## Custom bed mest probes
+## Prusa has 3x3 or 7x7, you can do any variation you want
+# [bed_mesh]
+# probe_count: 4,4
+
+# Linear correction
+# Check `extruders/linear-correction` for more informations.
+[include klipper-prusa-mk3s/extruders/linear-correction/linear-correction-0.cfg] # Default Prusa linear correction optimized for LDO motors
+
+### MACROS
+[include klipper-prusa-mk3s/macros.cfg]
+
+# FIRST RUN: 
+# Execute these sequentially in the console, let PID tuning finish before saving
+# PID_CALIBRATE HEATER=extruder TARGET=170
+# SAVE_CONFIG
+# PID_CALIBRATE HEATER=heater_bed TARGET=60
+# SAVE_CONFIG
+
+# You can also skip the above setting for stock Prusa and use
+[extruder]
+#control: pid
+min_temp: 0
+max_temp: 305
+min_extrude_temp: 170
+
+[stepper_z]
+position_max: 210
+
+[heater_bed]
+pid_Kp=54.241
+pid_Ki=0.646
+pid_Kd=1139.053
+
+### The end, on the end the printer will store it's tuning data, so do not edit it.
+
+#*# <---------------------- SAVE_CONFIG ---------------------->
+#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
+#*#
+#*# [extruder]
+#*# control = pid
+#*# pid_kp = 25.678
+#*# pid_ki = 1.297
+#*# pid_kd = 127.106