k-space/voron-config
11
0
Fork 0
Code Issues Pull Requests Actions Packages Projects Activity

Automatic backup: 2025-07-09_20:00:01

Browse Source
This commit is contained in:
voron-automated
2025-07-09 20:00:01 +03:00
parent 74fcabc619
commit a2e4a495b4
2 changed files with 812 additions and 9 deletions
Download Patch File Download Diff File Expand all files Collapse all files

803
printer-20250708_221324.cfg Normal file
View File

@@ -0,0 +1,803 @@
## Voron Design VORON2 250/300/350mm Spider TMC2209 UART config
## *** THINGS TO CHANGE/CHECK: ***
## MCU paths [mcu] section
## Thermistor types [extruder] and [heater_bed] sections - See 'sensor types' list at end of file
## Z Endstop Switch location [safe_z_home] section
## Homing end position [gcode_macro G32] section
## Z Endstop Switch offset for Z0 [stepper_z] section
## Probe points [quad_gantry_level] section
## Min & Max gantry corner postions [quad_gantry_level] section
## PID tune [extruder] and [heater_bed] sections
## Fine tune E steps [extruder] section
[mcu]
## Obtain definition by "ls -l /dev/serial/by-id/"
##--------------------------------------------------------------------
serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_420029001151383039343538-if00
## Uncomment below if you're using the Raspberry uart0 to communicate with Spider
#restart_method: command
[printer]
kinematics: corexy
max_velocity: 300
max_accel: 3000 #Max 4000
max_z_velocity: 15 #Max 15 for 12V TMC Drivers, can increase for 24V
max_z_accel: 350
square_corner_velocity: 5.0
#####################################################################
# X/Y Stepper Settings
#####################################################################
[stepper_x]
## Connected to X-MOT (B Motor)
step_pin: PE11
dir_pin: PE10
enable_pin: !PE9
rotation_distance: 40
microsteps: 32
full_steps_per_rotation:400 #set to 400 for 0.9 degree stepper
endstop_pin: ^PA1
position_min: 0
##--------------------------------------------------------------------
## Uncomment below for 250mm build
#position_endstop: 250
#position_max: 250
## Uncomment for 300mm build
position_endstop: 300
position_max: 300
# Uncomment for 350mm build
# position_endstop: 350
# position_max: 350
##--------------------------------------------------------------------
homing_speed: 100 #Max 100
homing_retract_dist: 5
homing_positive_dir: true
## Make sure to update below for your relevant driver (2208 or 2209)
[tmc2209 stepper_x]
uart_pin: PE7
interpolate: False
run_current: 0.8
sense_resistor: 0.110
stealthchop_threshold: 0
[stepper_y]
## Connected to Y-MOT (A Motor)
step_pin: PD8
dir_pin: PB12
enable_pin: !PD9
rotation_distance: 40
microsteps: 32
full_steps_per_rotation:400 #set to 400 for 0.9 degree stepper
endstop_pin: ^PA2
position_min: -10
##--------------------------------------------------------------------
## Uncomment for 250mm build
#position_endstop: 250
#position_max: 250
## Uncomment for 300mm build
position_endstop: 300
position_max: 300
# Uncomment for 350mm build
# position_endstop: 355
# position_max: 355
##--------------------------------------------------------------------
homing_speed: 100 #Max 100
homing_retract_dist: 5
homing_positive_dir: true
## Make sure to update below for your relevant driver (2208 or 2209)
[tmc2209 stepper_y]
uart_pin: PE15
interpolate: False
run_current: 0.8
sense_resistor: 0.110
stealthchop_threshold: 0
#####################################################################
# Z Stepper Settings
#####################################################################
## In Z-MOT Position
## Z0 Stepper - Front Left
[stepper_z]
step_pin: PD14
dir_pin: !PD13
enable_pin: !PD15
rotation_distance: 40
gear_ratio: 80:16
microsteps: 32
## In Z- Position
endstop_pin: ^PA0
## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0)
## (+) value = endstop above Z0, (-) value = endstop below
## Increasing position_endstop brings nozzle closer to the bed
## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config
#position_endstop: 0
##--------------------------------------------------------------------
## Uncomment below for 250mm build
#position_max: 230
## Uncomment below for 300mm build
position_max: 280
# # Uncomment below for 350mm build
# position_max: 295
##--------------------------------------------------------------------
position_min: -5
homing_speed: 8
second_homing_speed: 3
homing_retract_dist: 3
## Make sure to update below for your relevant driver (2208 or 2209)
[tmc2209 stepper_z]
uart_pin: PD10
interpolate: False
run_current: 0.8
sense_resistor: 0.110
stealthchop_threshold: 0
## In E1-MOT Position
## Z1 Stepper - Rear Left
[stepper_z1]
step_pin: PE6
dir_pin: PC13
enable_pin: !PE5
rotation_distance: 40
gear_ratio: 80:16
microsteps: 32
## Make sure to update below for your relevant driver (2208 or 2209)
[tmc2209 stepper_z1]
uart_pin: PC14
interpolate: False
run_current: 0.8
sense_resistor: 0.110
stealthchop_threshold: 0
## In E2-MOT Position
## Z2 Stepper - Rear Right
[stepper_z2]
step_pin: PE2
dir_pin: !PE4
enable_pin: !PE3
rotation_distance: 40
gear_ratio: 80:16
microsteps: 32
## Make sure to update below for your relevant driver (2208 or 2209)
[tmc2209 stepper_z2]
uart_pin: PC15
interpolate: False
run_current: 0.8
sense_resistor: 0.110
stealthchop_threshold: 0
## In E3-MOT Position
## Z3 Stepper - Front Right
[stepper_z3]
step_pin: PD12
dir_pin: PC4
enable_pin: !PE8
rotation_distance: 40
gear_ratio: 80:16
microsteps: 32
[tmc2209 stepper_z3]
uart_pin: PA15
interpolate: False
run_current: 0.8
sense_resistor: 0.110
stealthchop_threshold: 0
#######################################
#### Enclosure Temp Sensor Section ####
#######################################
# [thermistor chamber_temp]
# temperature1: 25
# resistance1: 10000
# beta: 3950
[temperature_sensor chamber]
sensor_type: PT1000
sensor_pin: PC1
min_temp: 0
max_temp: 100
gcode_id: C
#####################################################################
# Extruder
#####################################################################
## In E0-MOT Position
[extruder]
step_pin: PD5
dir_pin: !PD6
enable_pin: !PD4
## Update value below when you perform extruder calibration
## If you ask for 100mm of filament, but in reality it is 98mm:
## rotation_distance = <previous_rotation_distance> * <actual_extrude_distance> / 100
## 22.6789511 is a good starting point for Bondtech 5mm gears
## 34.37086 for Bondtech 8mm gears (Galileo)
rotation_distance: 22.90574
## Update Gear Ratio depending on your Extruder Type
## Use 50:17 for Afterburner/Clockwork (BMG Gear Ratio)
## Use 80:20 for M4, M3.1
## Use 7.5:1 for Galileo
gear_ratio: 50:10 #BMG Gear Ratio
microsteps: 32
full_steps_per_rotation: 200 #200 for 1.8 degree, 400 for 0.9 degree
nozzle_diameter: 0.400
filament_diameter: 1.75
## In E0 OUT Position
heater_pin: PB15
## Validate the following thermistor type to make sure it is correct
sensor_type: ATC Semitec 104NT-4-R025H42G
sensor_pin: PC0
min_temp: 10
max_temp: 270
max_power: 1.0
min_extrude_temp: 200
max_extrude_only_distance: 101
#control = pid
#pid_kp = 26.213
#pid_ki = 1.304
#pid_kd = 131.721
# Try to keep pressure_advance below 1.0
pressure_advance: 0.032
# Default is 0.040, leave stock
pressure_advance_smooth_time: 0.040
## In E0-MOT Position
## Make sure to update below for your relevant driver (2208 or 2209)
[tmc2209 extruder]
uart_pin: PD7
interpolate: false
run_current: 0.5
hold_current: 0.2
sense_resistor: 0.110
stealthchop_threshold: 0
[filament_switch_sensor switch_sensor]
switch_pin: PB1
pause_on_runout: False
runout_gcode:
PAUSE # [pause_resume] is required in printer.cfg
M117 Filament switch runout
insert_gcode:
M117 Filament switch inserted
[filament_motion_sensor encoder_sensor]
switch_pin: PB13
detection_length: 7
extruder: extruder
pause_on_runout: False
runout_gcode:
# Detect but do nothing as it is triggering too much
#PAUSE # [pause_resume] is required in printer.cfg
M117 Filament encoder runout
insert_gcode:
M117 Filament encoder inserted
[gcode_macro F_CONSUMED]
variable_filament_consumed: 0
variable_filament_lenght: 20 # length between the sensor and extruder
gcode:
# save current filament consumption
SET_GCODE_VARIABLE MACRO=F_CONSUMED VARIABLE=filament_consumed VALUE={printer.print_stats.filament_used}
# start checking filament consumption
UPDATE_DELAYED_GCODE ID=DELAY_M600 DURATION=1
[delayed_gcode DELAY_M600]
gcode:
# use set for easier reading
{% set consumed=printer["gcode_macro F_CONSUMED"].filament_consumed %}
{% set length=printer["gcode_macro F_CONSUMED"].filament_lenght %}
# check if predetermine length is reached
{% if printer.print_stats.filament_used|float <= (consumed|float + length|float) %}
# start looping this script every second
UPDATE_DELAYED_GCODE ID=DELAY_M600 DURATION=1
{% else %}
error_tones
PAUSE
{% endif %}
#####################################################################
# Bed Heater
#####################################################################
[heater_bed]
## SSR Pin - In BED OUT position
heater_pin: PC8
sensor_type: Generic 3950
sensor_pin: PB0 # TB Position
## Adjust Max Power so your heater doesn't warp your bed
max_power: 1
min_temp: 0
max_temp: 120
control: pid
pid_kp: 59.854
pid_ki: 1.596
pid_kd: 561.133
#####################################################################
# Probe
#####################################################################
[probe]
## This probe is not used for Z height, only Quad Gantry Leveling
## In Z+ position
## If your probe is NO instead of NC, change pin to ^!PA3
pin: ^PA3
x_offset: 0
y_offset: 25.0
#z_offset: 0
speed: 10.0
samples: 3
samples_result: median
sample_retract_dist: 3.0
samples_tolerance: 0.012
samples_tolerance_retries: 3
#####################################################################
# Fan Control
#####################################################################
[heater_fan hotend_fan]
## Hotend Fan - FAN0 Connector
pin: PA13
max_power: 1.0
kick_start_time: 0.5
heater: extruder
heater_temp: 50.0
## If you are experiencing back flow, you can reduce fan_speed
#fan_speed: 1.0
[fan]
## Print Cooling Fan - FAN1 Connector
## Uncomment below for SpiderVersion 1.x
#pin: PB1
## Uncomment below for SpiderVersion 2.2
pin: PA14
max_power: 1
kick_start_time: 0.5
## Depending on your fan, you may need to increase this value
## if your fan will not start. Can change cycle_time (increase)
## if your fan is not able to slow down effectively
off_below: 0.10
[heater_fan controller_fan]
## Exhaust fan - In E2 OUT Positon
pin: PB3
max_power: 1.0
shutdown_speed: 0.0
kick_start_time: 5.0
heater: heater_bed
heater_temp: 60
fan_speed: 1.0
[heater_fan nevermore_fan]
# nevermore fan in fan3 connector
pin: PB2
max_power: 1.0
shutdown_speed: 0.0
kick_start_time: 5.0
heater: heater_bed
heater_temp: 60
fan_speed: 1.0
#####################################################################
# LED Control
#####################################################################
#[output_pin caselight ]
## Chamber Lighting - In E1 OUT Position
#pin: PC8
#pwm: true
#shutdown_value: 0
#cycle_time: 0.01
#####################################################################
# Homing and Gantry Adjustment Routines
#####################################################################
[idle_timeout]
timeout: 1800
[safe_z_home]
## XY Location of the Z Endstop Switch
## Update -10,-10 to the XY coordinates of your endstop pin
## (such as 157,305) after going through Z Endstop Pin
## Location Definition step.
home_xy_position:209,300
speed:100
z_hop:10
[quad_gantry_level]
## Use QUAD_GANTRY_LEVEL to level a gantry.
## Min & Max gantry corners - measure from nozzle at MIN (0,0) and
## MAX (250, 250), (300,300), or (350,350) depending on your printer size
## to respective belt positions
#--------------------------------------------------------------------
## Gantry Corners for 250mm Build
## Uncomment for 250mm build
#gantry_corners:
# -60,-10
# 310, 320
## Probe points
#points:
# 50,25
# 50,175
# 200,175
# 200,25
# Gantry Corners for 300mm Build
# Uncomment for 300mm build
gantry_corners:
-60,-10
360,370
# Probe points
points:
50,25
50,225
250,225
250,25
# # Gantry Corners for 350mm Build
# # Uncomment for 350mm build
# gantry_corners:
# -60,-10
# 410,420
# # Probe points
# points:
# 50,25
# 50,275
# 300,275
# 300,25
#--------------------------------------------------------------------
speed: 200
horizontal_move_z: 10
retries: 5
retry_tolerance: 0.0075
max_adjust: 10
[bed_mesh]
speed: 300
horizontal_move_z: 10
##--------------------------------------------------------------------
## Uncomment below for 250mm build
#mesh_min: 40, 40
#mesh_max: 210,210
# Uncomment for 300mm build
mesh_min: 40, 40
mesh_max: 260,260
zero_reference_position: 150,150
# # Uncomment for 350mm build
# mesh_min: 40, 40
# mesh_max: 310,310
##--------------------------------------------------------------------
fade_start: 0.6
fade_end: 10.0
probe_count: 9,9
algorithm: bicubic
#relative_reference_index: 40
#####################################################################
# Displays
#####################################################################
#--------------------------------------------------------------------
[display]
# mini12864 LCD Display
lcd_type: uc1701
cs_pin: PC11
a0_pin: PD2
rst_pin: PC10
encoder_pins: ^PC6,^PC7
click_pin: ^!PA8
contrast: 63
#spi_bus: spi1
spi_software_mosi_pin: PA7
spi_software_miso_pin: PA6
spi_software_sclk_pin: PA5
[neopixel fysetc_mini12864]
# To control Neopixel RGB in mini12864 display
pin: PC12
chain_count: 3
initial_RED: 0.1
initial_GREEN: 0.5
initial_BLUE: 0.0
color_order: RGB
# Set RGB values on boot up for each Neopixel.
# Index 1 = display, Index 2 and 3 = Knob
[delayed_gcode setdisplayneopixel]
initial_duration: 1
gcode:
SET_LED LED=fysetc_mini12864 RED=1 GREEN=1 BLUE=1 INDEX=1 TRANSMIT=0
SET_LED LED=fysetc_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=2 TRANSMIT=0
SET_LED LED=fysetc_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=3
#--------------------------------------------------------------------
#####################################################################
# Macros
#####################################################################
[gcode_macro CENTER]
gcode:
G0 X150 Y150 Z30 F3600
[gcode_macro G32]
gcode:
SAVE_GCODE_STATE NAME=STATE_G32
G90
G28
QUAD_GANTRY_LEVEL
G28
## Uncomment for for your size printer:
#--------------------------------------------------------------------
## Uncomment for 250mm build
#G0 X125 Y125 Z30 F3600
## Uncomment for 300 build
G0 X150 Y150 Z30 F3600
## Uncomment for 350mm build
# G0 X175 Y175 Z30 F3600
#--------------------------------------------------------------------
RESTORE_GCODE_STATE NAME=STATE_G32
[gcode_macro PRINT_START]
# Use PRINT_START for the slicer starting script - please customise for your slicer of choice
gcode:
# This part fetches data from your slicer. Such as bed, extruder, and chamber temps and size of your printer.
{% set target_bed = params.BED|int %}
{% set target_extruder = params.EXTRUDER|int %}
{% set target_chamber = params.CHAMBER|default("45")|int %}
{% set x_wait = printer.toolhead.axis_maximum.x|float / 2 %}
{% set y_wait = printer.toolhead.axis_maximum.y|float / 2 %}
## Uncomment for Beacon Contact (1 of 4 for beacon contact)
#SET_GCODE_OFFSET Z=0 # Set offset to 0
# Home the printer, set absolute positioning and update the Stealthburner LEDs.
STATUS_HOMING # Set LEDs to homing-mode
G28 # Full home (XYZ)
G90 # Absolute position
## Uncomment for bed mesh (1 of 2 for bed mesh)
#BED_MESH_CLEAR # Clear old saved bed mesh (if any)
# Check if the bed temp is higher than 90c - if so then trigger a heatsoak.
#{% if params.BED|int > 90 %}
#SET_DISPLAY_TEXT MSG="Bed: {target_bed}c" # Display info on display
#STATUS_HEATING # Set LEDs to heating-mode
#M106 S255 # Turn on the PT-fan
## Uncomment if you have a Nevermore.
#SET_PIN PIN=nevermore VALUE=1 # Turn on the nevermore
#G1 X{x_wait} Y{y_wait} Z15 F9000 # Go to center of the bed
#M190 S{target_bed} # Set the target temp for the bed
#SET_DISPLAY_TEXT MSG="Heatsoak: {target_chamber}c" # Display info on display
#TEMPERATURE_WAIT SENSOR="temperature_sensor chamber" MINIMUM={target_chamber} # Waits for chamber temp
# If the bed temp is not over 90c, then skip the heatsoak and just heat up to set temp with a 5 min soak
#{% else %}
#SET_DISPLAY_TEXT MSG="Bed: {target_bed}c" # Display info on display
#STATUS_HEATING # Set LEDs to heating-mode
#G1 X{x_wait} Y{y_wait} Z15 F9000 # Go to center of the bed
#M190 S{target_bed} # Set the target temp for the bed
#SET_DISPLAY_TEXT MSG="Soak for 5 min" # Display info on display
#G4 P300000 # Wait 5 min for the bedtemp to stabilize
#{% endif %}
# Heat hotend to 150c. This helps with getting a correct Z-home.
SET_DISPLAY_TEXT MSG="Hotend: 150c" # Display info on display
M109 S150 # Heat hotend to 150c
## Uncomment for Beacon contact (2 of 4 for beacon contact)
#G28 Z METHOD=CONTACT CALIBRATE=1 # Calibrate z offset and beacon model
## Uncomment for Trident (Z_TILT_ADJUST)
#SET_DISPLAY_TEXT MSG="Leveling" # Display info on display
#STATUS_LEVELING # Set LEDs to leveling-mode
#Z_TILT_ADJUST # Level the printer via Z_TILT_ADJUST
#G28 Z # Home Z again after Z_TILT_ADJUST
## Uncomment for V2.4 (Quad gantry level AKA QGL)
SET_DISPLAY_TEXT MSG="Bed: {target_bed}c"
M140 S{target_bed}
SET_DISPLAY_TEXT MSG="Leveling" # Display info on display
STATUS_LEVELING # Set LEDs to leveling-mode
QUAD_GANTRY_LEVEL # Level the printer via QGL
G28 Z # Home Z again after QGL
## Uncomment for bed mesh (2 of 2 for bed mesh)
#SET_DISPLAY_TEXT MSG="Bed mesh" # Display info on display
#STATUS_MESHING # Set LEDs to bed mesh-mode
#BED_MESH_CALIBRATE # Start the bed mesh (add ADAPTIVE=1) for adaptive bed mesh
## Uncomment for Beacon Contact (3 of 4 for beacon contact)
#G28 Z METHOD=CONTACT CALIBRATE=0 # Calibrate z offset only with hot nozzle
# Heat up the hotend up to target via data from slicer
SET_DISPLAY_TEXT MSG="Hotend: {target_extruder}c" # Display info on display
STATUS_HEATING # Set LEDs to heating-mode
G1 X{x_wait} Y{y_wait} Z15 F9000 # Go to center of the bed
M107 # Turn off partcooling fan
M109 S{target_extruder} # Heat the hotend to set temp
## Uncomment for Beacon Contact (4 of 4 for beacon contact)
#SET_GCODE_OFFSET Z=0.06 # Add a little offset for hotend thermal expansion
# Get ready to print by doing a primeline and updating the LEDs
SET_DISPLAY_TEXT MSG="Printer goes brr" # Display info on display
STATUS_PRINTING # Set LEDs to printing-mode
G0 X{x_wait - 50} Y4 F10000 # Go to starting point
G0 Z0.4 # Raise Z to 0.4
G91 # Incremental positioning
G1 X100 E20 F1000 # Primeline
G90 # Absolute position
[gcode_macro PRINT_END]
# Use PRINT_END for the slicer ending script - please customise for your slicer of choice
gcode:
M400 ; wait for buffer to clear
G92 E0 ; zero the extruder
G1 E-5 F1800 ; retract filament
G91 ; relative positioning
G0 Z1.00 X20.0 Y20.0 F20000 ; move nozzle to remove stringing
TURN_OFF_HEATERS
M107 ; turn off fan
G1 Z2 F3000 ; move nozzle up 2mm
G90 ; absolute positioning
G0 X125 Y250 F3600 ; park nozzle at rear
BED_MESH_CLEAR
end_tones
######################################################################
# Beeper
######################################################################
# M300 : Play tone. Beeper support, as commonly found on usual LCD
# displays (i.e. RepRapDiscount 2004 Smart Controller, RepRapDiscount
# 12864 Full Graphic). This defines a custom I/O pin and a custom
# GCODE macro. Usage:
# M300 [P<ms>] [S<Hz>]
# P is the tone duration, S the tone frequency.
# The frequency won't be pitch perfect.
[output_pin BEEPER_pin]
pin: PC9
# Beeper pin. This parameter must be provided.
# ar37 is the default RAMPS/MKS pin.
pwm: True
# A piezo beeper needs a PWM signal, a DC buzzer doesn't.
value: 0
# Silent at power on, set to 1 if active low.
shutdown_value: 0
# Disable at emergency shutdown (no PWM would be available anyway).
cycle_time: 0.001
# Default PWM frequency : 0.001 = 1ms will give a tone of 1kHz
# Although not pitch perfect.
[gcode_macro M300]
gcode:
# Use a default 1kHz tone if S is omitted.
{% set S = params.S|default(1000)|int %}
# Use a 10ms duration is P is omitted.
{% set P = params.P|default(100)|int %}
SET_PIN PIN=BEEPER_pin VALUE=0.5 CYCLE_TIME={ 1.0/S if S > 0 else 1 }
G4 P{P}
SET_PIN PIN=BEEPER_pin VALUE=0
[gcode_macro start_tones]
gcode:
M300 S1000 P500 ; chirp to indicate starting to print
[gcode_macro end_tones]
gcode:
M300 S440 P200 ; Make Print Completed Tones
M300 S660 P250
M300 S880 P300
[gcode_macro error_tones]
gcode:
M300 S700 P1500 ; Make Print Completed Tones
M300 S700 P500 ; Make Print Completed Tones
M300 S700 P500 ; Make Print Completed Tones
M300 S700 P500 ; Make Print Completed Tones
M300 S700 P500 ; Make Print Completed Tones
M300 S700 P500 ; Make Print Completed Tones
M300 S700 P500 ; Make Print Completed Tones
M300 S700 P500 ; Make Print Completed Tones
[include fluidd.cfg]
[include leds.cfg]
[include tones.cfg]
[exclude_object]
[virtual_sdcard]
path: /home/pi/printer_data/gcodes
## Common Temperature Sensors
## "EPCOS 100K B57560G104F"
## "ATC Semitec 104GT-2"
## "NTC 100K beta 3950"
## "Honeywell 100K 135-104LAG-J01"
## "NTC 100K MGB18-104F39050L32" (Keenovo Heater Pad)
## "AD595"
## "PT100 INA826"
## "PT1000"
#*# <---------------------- SAVE_CONFIG ---------------------->
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
#*#
#*# [extruder]
#*# control = pid
#*# pid_kp = 26.862
#*# pid_ki = 1.926
#*# pid_kd = 93.682
#*#
#*# [stepper_z]
#*# position_endstop = 1.640
#*#
#*# [bed_mesh default]
#*# version = 1
#*# points =
#*# 0.043750, 0.087500, 0.108750, 0.118750, 0.105000, 0.092500, 0.078750, 0.063750, 0.041250
#*# 0.012500, 0.053750, 0.076250, 0.085000, 0.066250, 0.052500, 0.043750, 0.025000, 0.005000
#*# -0.015000, 0.027500, 0.046250, 0.048750, 0.035000, 0.017500, 0.003750, -0.016250, -0.037500
#*# -0.021250, 0.020000, 0.037500, 0.041250, 0.021250, 0.006250, -0.006250, -0.027500, -0.048750
#*# -0.037500, -0.003750, 0.012500, 0.016250, 0.000000, -0.020000, -0.032500, -0.042500, -0.060000
#*# -0.036250, -0.003750, 0.012500, 0.013750, -0.007500, -0.025000, -0.033750, -0.047500, -0.067500
#*# -0.031250, -0.001250, 0.013750, 0.018750, 0.003750, -0.011250, -0.023750, -0.035000, -0.051250
#*# -0.016250, 0.020000, 0.031250, 0.035000, 0.021250, 0.006250, -0.003750, -0.015000, -0.030000
#*# 0.006250, 0.035000, 0.048750, 0.051250, 0.037500, 0.027500, 0.018750, 0.008750, -0.007500
#*# tension = 0.2
#*# min_x = 40.0
#*# algo = bicubic
#*# y_count = 9
#*# mesh_y_pps = 2
#*# min_y = 40.0
#*# x_count = 9
#*# max_y = 260.0
#*# mesh_x_pps = 2
#*# max_x = 260.0
#*#
#*# [probe]
#*# z_offset = -0.010