diff --git a/printer-20250708_221324.cfg b/printer-20250708_221324.cfg new file mode 100644 index 0000000..cfbeb08 --- /dev/null +++ b/printer-20250708_221324.cfg @@ -0,0 +1,803 @@ +## Voron Design VORON2 250/300/350mm Spider TMC2209 UART config + +## *** THINGS TO CHANGE/CHECK: *** +## MCU paths [mcu] section +## Thermistor types [extruder] and [heater_bed] sections - See 'sensor types' list at end of file +## Z Endstop Switch location [safe_z_home] section +## Homing end position [gcode_macro G32] section +## Z Endstop Switch offset for Z0 [stepper_z] section +## Probe points [quad_gantry_level] section +## Min & Max gantry corner postions [quad_gantry_level] section +## PID tune [extruder] and [heater_bed] sections +## Fine tune E steps [extruder] section + +[mcu] +## Obtain definition by "ls -l /dev/serial/by-id/" +##-------------------------------------------------------------------- +serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_420029001151383039343538-if00 + +## Uncomment below if you're using the Raspberry uart0 to communicate with Spider +#restart_method: command + +[printer] +kinematics: corexy +max_velocity: 300 +max_accel: 3000 #Max 4000 +max_z_velocity: 15 #Max 15 for 12V TMC Drivers, can increase for 24V +max_z_accel: 350 +square_corner_velocity: 5.0 + +##################################################################### +# X/Y Stepper Settings +##################################################################### + +[stepper_x] +## Connected to X-MOT (B Motor) +step_pin: PE11 +dir_pin: PE10 +enable_pin: !PE9 +rotation_distance: 40 +microsteps: 32 +full_steps_per_rotation:400 #set to 400 for 0.9 degree stepper +endstop_pin: ^PA1 +position_min: 0 + +##-------------------------------------------------------------------- + +## Uncomment below for 250mm build +#position_endstop: 250 +#position_max: 250 + +## Uncomment for 300mm build +position_endstop: 300 +position_max: 300 + +# Uncomment for 350mm build +# position_endstop: 350 +# position_max: 350 + +##-------------------------------------------------------------------- +homing_speed: 100 #Max 100 +homing_retract_dist: 5 +homing_positive_dir: true + +## Make sure to update below for your relevant driver (2208 or 2209) +[tmc2209 stepper_x] +uart_pin: PE7 +interpolate: False +run_current: 0.8 +sense_resistor: 0.110 +stealthchop_threshold: 0 + +[stepper_y] +## Connected to Y-MOT (A Motor) +step_pin: PD8 +dir_pin: PB12 +enable_pin: !PD9 +rotation_distance: 40 +microsteps: 32 +full_steps_per_rotation:400 #set to 400 for 0.9 degree stepper +endstop_pin: ^PA2 +position_min: -10 +##-------------------------------------------------------------------- + +## Uncomment for 250mm build +#position_endstop: 250 +#position_max: 250 + +## Uncomment for 300mm build +position_endstop: 300 +position_max: 300 + +# Uncomment for 350mm build +# position_endstop: 355 +# position_max: 355 + +##-------------------------------------------------------------------- +homing_speed: 100 #Max 100 +homing_retract_dist: 5 +homing_positive_dir: true + +## Make sure to update below for your relevant driver (2208 or 2209) +[tmc2209 stepper_y] +uart_pin: PE15 +interpolate: False +run_current: 0.8 +sense_resistor: 0.110 +stealthchop_threshold: 0 + +##################################################################### +# Z Stepper Settings +##################################################################### + +## In Z-MOT Position +## Z0 Stepper - Front Left +[stepper_z] +step_pin: PD14 +dir_pin: !PD13 +enable_pin: !PD15 +rotation_distance: 40 +gear_ratio: 80:16 +microsteps: 32 +## In Z- Position +endstop_pin: ^PA0 +## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0) +## (+) value = endstop above Z0, (-) value = endstop below +## Increasing position_endstop brings nozzle closer to the bed +## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config +#position_endstop: 0 +##-------------------------------------------------------------------- + +## Uncomment below for 250mm build +#position_max: 230 + +## Uncomment below for 300mm build +position_max: 280 + +# # Uncomment below for 350mm build +# position_max: 295 + +##-------------------------------------------------------------------- +position_min: -5 +homing_speed: 8 +second_homing_speed: 3 +homing_retract_dist: 3 + +## Make sure to update below for your relevant driver (2208 or 2209) +[tmc2209 stepper_z] +uart_pin: PD10 +interpolate: False +run_current: 0.8 +sense_resistor: 0.110 +stealthchop_threshold: 0 + +## In E1-MOT Position +## Z1 Stepper - Rear Left +[stepper_z1] +step_pin: PE6 +dir_pin: PC13 +enable_pin: !PE5 +rotation_distance: 40 +gear_ratio: 80:16 +microsteps: 32 + +## Make sure to update below for your relevant driver (2208 or 2209) +[tmc2209 stepper_z1] +uart_pin: PC14 +interpolate: False +run_current: 0.8 +sense_resistor: 0.110 +stealthchop_threshold: 0 + +## In E2-MOT Position +## Z2 Stepper - Rear Right +[stepper_z2] +step_pin: PE2 +dir_pin: !PE4 +enable_pin: !PE3 +rotation_distance: 40 +gear_ratio: 80:16 +microsteps: 32 + +## Make sure to update below for your relevant driver (2208 or 2209) +[tmc2209 stepper_z2] +uart_pin: PC15 +interpolate: False +run_current: 0.8 +sense_resistor: 0.110 +stealthchop_threshold: 0 + +## In E3-MOT Position +## Z3 Stepper - Front Right +[stepper_z3] +step_pin: PD12 +dir_pin: PC4 +enable_pin: !PE8 +rotation_distance: 40 +gear_ratio: 80:16 +microsteps: 32 + +[tmc2209 stepper_z3] +uart_pin: PA15 +interpolate: False +run_current: 0.8 +sense_resistor: 0.110 +stealthchop_threshold: 0 + +####################################### +#### Enclosure Temp Sensor Section #### +####################################### +# [thermistor chamber_temp] +# temperature1: 25 +# resistance1: 10000 +# beta: 3950 + + +[temperature_sensor chamber] +sensor_type: PT1000 +sensor_pin: PC1 +min_temp: 0 +max_temp: 100 +gcode_id: C + +##################################################################### +# Extruder +##################################################################### + +## In E0-MOT Position +[extruder] +step_pin: PD5 +dir_pin: !PD6 +enable_pin: !PD4 + +## Update value below when you perform extruder calibration +## If you ask for 100mm of filament, but in reality it is 98mm: +## rotation_distance = * / 100 +## 22.6789511 is a good starting point for Bondtech 5mm gears +## 34.37086 for Bondtech 8mm gears (Galileo) +rotation_distance: 22.90574 +## Update Gear Ratio depending on your Extruder Type +## Use 50:17 for Afterburner/Clockwork (BMG Gear Ratio) +## Use 80:20 for M4, M3.1 +## Use 7.5:1 for Galileo + +gear_ratio: 50:10 #BMG Gear Ratio +microsteps: 32 +full_steps_per_rotation: 200 #200 for 1.8 degree, 400 for 0.9 degree +nozzle_diameter: 0.400 +filament_diameter: 1.75 +## In E0 OUT Position +heater_pin: PB15 +## Validate the following thermistor type to make sure it is correct +sensor_type: ATC Semitec 104NT-4-R025H42G +sensor_pin: PC0 +min_temp: 10 +max_temp: 270 +max_power: 1.0 +min_extrude_temp: 200 +max_extrude_only_distance: 101 +#control = pid +#pid_kp = 26.213 +#pid_ki = 1.304 +#pid_kd = 131.721 +# Try to keep pressure_advance below 1.0 +pressure_advance: 0.032 +# Default is 0.040, leave stock +pressure_advance_smooth_time: 0.040 + +## In E0-MOT Position +## Make sure to update below for your relevant driver (2208 or 2209) +[tmc2209 extruder] +uart_pin: PD7 +interpolate: false +run_current: 0.5 +hold_current: 0.2 +sense_resistor: 0.110 +stealthchop_threshold: 0 + +[filament_switch_sensor switch_sensor] +switch_pin: PB1 +pause_on_runout: False +runout_gcode: + PAUSE # [pause_resume] is required in printer.cfg + M117 Filament switch runout +insert_gcode: + M117 Filament switch inserted + +[filament_motion_sensor encoder_sensor] +switch_pin: PB13 +detection_length: 7 +extruder: extruder +pause_on_runout: False +runout_gcode: + # Detect but do nothing as it is triggering too much + #PAUSE # [pause_resume] is required in printer.cfg + M117 Filament encoder runout +insert_gcode: + M117 Filament encoder inserted + +[gcode_macro F_CONSUMED] +variable_filament_consumed: 0 +variable_filament_lenght: 20 # length between the sensor and extruder +gcode: + # save current filament consumption + SET_GCODE_VARIABLE MACRO=F_CONSUMED VARIABLE=filament_consumed VALUE={printer.print_stats.filament_used} + # start checking filament consumption + UPDATE_DELAYED_GCODE ID=DELAY_M600 DURATION=1 + +[delayed_gcode DELAY_M600] +gcode: + # use set for easier reading + {% set consumed=printer["gcode_macro F_CONSUMED"].filament_consumed %} + {% set length=printer["gcode_macro F_CONSUMED"].filament_lenght %} + # check if predetermine length is reached + {% if printer.print_stats.filament_used|float <= (consumed|float + length|float) %} + # start looping this script every second + UPDATE_DELAYED_GCODE ID=DELAY_M600 DURATION=1 + {% else %} + error_tones + PAUSE + {% endif %} + + +##################################################################### +# Bed Heater +##################################################################### +[heater_bed] +## SSR Pin - In BED OUT position +heater_pin: PC8 +sensor_type: Generic 3950 +sensor_pin: PB0 # TB Position +## Adjust Max Power so your heater doesn't warp your bed +max_power: 1 +min_temp: 0 +max_temp: 120 +control: pid +pid_kp: 59.854 +pid_ki: 1.596 +pid_kd: 561.133 + +##################################################################### +# Probe +##################################################################### + +[probe] +## This probe is not used for Z height, only Quad Gantry Leveling +## In Z+ position +## If your probe is NO instead of NC, change pin to ^!PA3 +pin: ^PA3 +x_offset: 0 +y_offset: 25.0 +#z_offset: 0 +speed: 10.0 +samples: 3 +samples_result: median +sample_retract_dist: 3.0 +samples_tolerance: 0.012 +samples_tolerance_retries: 3 + +##################################################################### +# Fan Control +##################################################################### + +[heater_fan hotend_fan] +## Hotend Fan - FAN0 Connector +pin: PA13 +max_power: 1.0 +kick_start_time: 0.5 +heater: extruder +heater_temp: 50.0 +## If you are experiencing back flow, you can reduce fan_speed +#fan_speed: 1.0 + +[fan] +## Print Cooling Fan - FAN1 Connector +## Uncomment below for SpiderVersion 1.x +#pin: PB1 +## Uncomment below for SpiderVersion 2.2 +pin: PA14 +max_power: 1 +kick_start_time: 0.5 +## Depending on your fan, you may need to increase this value +## if your fan will not start. Can change cycle_time (increase) +## if your fan is not able to slow down effectively +off_below: 0.10 + +[heater_fan controller_fan] +## Exhaust fan - In E2 OUT Positon +pin: PB3 +max_power: 1.0 +shutdown_speed: 0.0 +kick_start_time: 5.0 +heater: heater_bed +heater_temp: 60 +fan_speed: 1.0 + +[heater_fan nevermore_fan] +# nevermore fan in fan3 connector +pin: PB2 +max_power: 1.0 +shutdown_speed: 0.0 +kick_start_time: 5.0 +heater: heater_bed +heater_temp: 60 +fan_speed: 1.0 + +##################################################################### +# LED Control +##################################################################### + +#[output_pin caselight ] +## Chamber Lighting - In E1 OUT Position +#pin: PC8 +#pwm: true +#shutdown_value: 0 +#cycle_time: 0.01 + +##################################################################### +# Homing and Gantry Adjustment Routines +##################################################################### + +[idle_timeout] +timeout: 1800 + +[safe_z_home] +## XY Location of the Z Endstop Switch +## Update -10,-10 to the XY coordinates of your endstop pin +## (such as 157,305) after going through Z Endstop Pin +## Location Definition step. +home_xy_position:209,300 +speed:100 +z_hop:10 + +[quad_gantry_level] +## Use QUAD_GANTRY_LEVEL to level a gantry. +## Min & Max gantry corners - measure from nozzle at MIN (0,0) and +## MAX (250, 250), (300,300), or (350,350) depending on your printer size +## to respective belt positions + +#-------------------------------------------------------------------- +## Gantry Corners for 250mm Build +## Uncomment for 250mm build +#gantry_corners: +# -60,-10 +# 310, 320 +## Probe points +#points: +# 50,25 +# 50,175 +# 200,175 +# 200,25 + +# Gantry Corners for 300mm Build +# Uncomment for 300mm build +gantry_corners: + -60,-10 + 360,370 +# Probe points +points: + 50,25 + 50,225 + 250,225 + 250,25 + +# # Gantry Corners for 350mm Build +# # Uncomment for 350mm build +# gantry_corners: +# -60,-10 +# 410,420 +# # Probe points +# points: +# 50,25 +# 50,275 +# 300,275 +# 300,25 + +#-------------------------------------------------------------------- +speed: 200 +horizontal_move_z: 10 +retries: 5 +retry_tolerance: 0.0075 +max_adjust: 10 + + +[bed_mesh] +speed: 300 +horizontal_move_z: 10 +##-------------------------------------------------------------------- +## Uncomment below for 250mm build +#mesh_min: 40, 40 +#mesh_max: 210,210 + +# Uncomment for 300mm build +mesh_min: 40, 40 +mesh_max: 260,260 +zero_reference_position: 150,150 + +# # Uncomment for 350mm build +# mesh_min: 40, 40 +# mesh_max: 310,310 +##-------------------------------------------------------------------- +fade_start: 0.6 +fade_end: 10.0 +probe_count: 9,9 +algorithm: bicubic +#relative_reference_index: 40 + +##################################################################### +# Displays +##################################################################### + +#-------------------------------------------------------------------- + +[display] +# mini12864 LCD Display +lcd_type: uc1701 +cs_pin: PC11 +a0_pin: PD2 +rst_pin: PC10 +encoder_pins: ^PC6,^PC7 +click_pin: ^!PA8 +contrast: 63 +#spi_bus: spi1 +spi_software_mosi_pin: PA7 +spi_software_miso_pin: PA6 +spi_software_sclk_pin: PA5 + +[neopixel fysetc_mini12864] +# To control Neopixel RGB in mini12864 display +pin: PC12 +chain_count: 3 +initial_RED: 0.1 +initial_GREEN: 0.5 +initial_BLUE: 0.0 +color_order: RGB + +# Set RGB values on boot up for each Neopixel. +# Index 1 = display, Index 2 and 3 = Knob +[delayed_gcode setdisplayneopixel] +initial_duration: 1 +gcode: + SET_LED LED=fysetc_mini12864 RED=1 GREEN=1 BLUE=1 INDEX=1 TRANSMIT=0 + SET_LED LED=fysetc_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=2 TRANSMIT=0 + SET_LED LED=fysetc_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=3 + +#-------------------------------------------------------------------- + + +##################################################################### +# Macros +##################################################################### + +[gcode_macro CENTER] +gcode: + G0 X150 Y150 Z30 F3600 + +[gcode_macro G32] +gcode: + SAVE_GCODE_STATE NAME=STATE_G32 + G90 + G28 + QUAD_GANTRY_LEVEL + G28 + + ## Uncomment for for your size printer: + #-------------------------------------------------------------------- + ## Uncomment for 250mm build + #G0 X125 Y125 Z30 F3600 + + ## Uncomment for 300 build + G0 X150 Y150 Z30 F3600 + + ## Uncomment for 350mm build + # G0 X175 Y175 Z30 F3600 + #-------------------------------------------------------------------- + RESTORE_GCODE_STATE NAME=STATE_G32 + + +[gcode_macro PRINT_START] +# Use PRINT_START for the slicer starting script - please customise for your slicer of choice +gcode: + # This part fetches data from your slicer. Such as bed, extruder, and chamber temps and size of your printer. + {% set target_bed = params.BED|int %} + {% set target_extruder = params.EXTRUDER|int %} + {% set target_chamber = params.CHAMBER|default("45")|int %} + {% set x_wait = printer.toolhead.axis_maximum.x|float / 2 %} + {% set y_wait = printer.toolhead.axis_maximum.y|float / 2 %} + + ## Uncomment for Beacon Contact (1 of 4 for beacon contact) + #SET_GCODE_OFFSET Z=0 # Set offset to 0 + + # Home the printer, set absolute positioning and update the Stealthburner LEDs. + STATUS_HOMING # Set LEDs to homing-mode + G28 # Full home (XYZ) + G90 # Absolute position + + ## Uncomment for bed mesh (1 of 2 for bed mesh) + #BED_MESH_CLEAR # Clear old saved bed mesh (if any) + + # Check if the bed temp is higher than 90c - if so then trigger a heatsoak. + #{% if params.BED|int > 90 %} + #SET_DISPLAY_TEXT MSG="Bed: {target_bed}c" # Display info on display + #STATUS_HEATING # Set LEDs to heating-mode + #M106 S255 # Turn on the PT-fan + + ## Uncomment if you have a Nevermore. + #SET_PIN PIN=nevermore VALUE=1 # Turn on the nevermore + + #G1 X{x_wait} Y{y_wait} Z15 F9000 # Go to center of the bed + #M190 S{target_bed} # Set the target temp for the bed + #SET_DISPLAY_TEXT MSG="Heatsoak: {target_chamber}c" # Display info on display + #TEMPERATURE_WAIT SENSOR="temperature_sensor chamber" MINIMUM={target_chamber} # Waits for chamber temp + + # If the bed temp is not over 90c, then skip the heatsoak and just heat up to set temp with a 5 min soak + #{% else %} + #SET_DISPLAY_TEXT MSG="Bed: {target_bed}c" # Display info on display + #STATUS_HEATING # Set LEDs to heating-mode + #G1 X{x_wait} Y{y_wait} Z15 F9000 # Go to center of the bed + #M190 S{target_bed} # Set the target temp for the bed + #SET_DISPLAY_TEXT MSG="Soak for 5 min" # Display info on display + #G4 P300000 # Wait 5 min for the bedtemp to stabilize + #{% endif %} + + # Heat hotend to 150c. This helps with getting a correct Z-home. + SET_DISPLAY_TEXT MSG="Hotend: 150c" # Display info on display + M109 S150 # Heat hotend to 150c + + ## Uncomment for Beacon contact (2 of 4 for beacon contact) + #G28 Z METHOD=CONTACT CALIBRATE=1 # Calibrate z offset and beacon model + + ## Uncomment for Trident (Z_TILT_ADJUST) + #SET_DISPLAY_TEXT MSG="Leveling" # Display info on display + #STATUS_LEVELING # Set LEDs to leveling-mode + #Z_TILT_ADJUST # Level the printer via Z_TILT_ADJUST + #G28 Z # Home Z again after Z_TILT_ADJUST + + ## Uncomment for V2.4 (Quad gantry level AKA QGL) + SET_DISPLAY_TEXT MSG="Bed: {target_bed}c" + M140 S{target_bed} + SET_DISPLAY_TEXT MSG="Leveling" # Display info on display + STATUS_LEVELING # Set LEDs to leveling-mode + QUAD_GANTRY_LEVEL # Level the printer via QGL + G28 Z # Home Z again after QGL + + ## Uncomment for bed mesh (2 of 2 for bed mesh) + #SET_DISPLAY_TEXT MSG="Bed mesh" # Display info on display + #STATUS_MESHING # Set LEDs to bed mesh-mode + #BED_MESH_CALIBRATE # Start the bed mesh (add ADAPTIVE=1) for adaptive bed mesh + + ## Uncomment for Beacon Contact (3 of 4 for beacon contact) + #G28 Z METHOD=CONTACT CALIBRATE=0 # Calibrate z offset only with hot nozzle + + # Heat up the hotend up to target via data from slicer + SET_DISPLAY_TEXT MSG="Hotend: {target_extruder}c" # Display info on display + STATUS_HEATING # Set LEDs to heating-mode + G1 X{x_wait} Y{y_wait} Z15 F9000 # Go to center of the bed + M107 # Turn off partcooling fan + M109 S{target_extruder} # Heat the hotend to set temp + + ## Uncomment for Beacon Contact (4 of 4 for beacon contact) + #SET_GCODE_OFFSET Z=0.06 # Add a little offset for hotend thermal expansion + + # Get ready to print by doing a primeline and updating the LEDs + SET_DISPLAY_TEXT MSG="Printer goes brr" # Display info on display + STATUS_PRINTING # Set LEDs to printing-mode + G0 X{x_wait - 50} Y4 F10000 # Go to starting point + G0 Z0.4 # Raise Z to 0.4 + G91 # Incremental positioning + G1 X100 E20 F1000 # Primeline + G90 # Absolute position + + +[gcode_macro PRINT_END] +# Use PRINT_END for the slicer ending script - please customise for your slicer of choice +gcode: + M400 ; wait for buffer to clear + G92 E0 ; zero the extruder + G1 E-5 F1800 ; retract filament + G91 ; relative positioning + G0 Z1.00 X20.0 Y20.0 F20000 ; move nozzle to remove stringing + TURN_OFF_HEATERS + M107 ; turn off fan + G1 Z2 F3000 ; move nozzle up 2mm + G90 ; absolute positioning + G0 X125 Y250 F3600 ; park nozzle at rear + BED_MESH_CLEAR + end_tones + + + +###################################################################### +# Beeper +###################################################################### + +# M300 : Play tone. Beeper support, as commonly found on usual LCD +# displays (i.e. RepRapDiscount 2004 Smart Controller, RepRapDiscount +# 12864 Full Graphic). This defines a custom I/O pin and a custom +# GCODE macro. Usage: +# M300 [P] [S] +# P is the tone duration, S the tone frequency. +# The frequency won't be pitch perfect. + +[output_pin BEEPER_pin] +pin: PC9 +# Beeper pin. This parameter must be provided. +# ar37 is the default RAMPS/MKS pin. +pwm: True +# A piezo beeper needs a PWM signal, a DC buzzer doesn't. +value: 0 +# Silent at power on, set to 1 if active low. +shutdown_value: 0 +# Disable at emergency shutdown (no PWM would be available anyway). +cycle_time: 0.001 +# Default PWM frequency : 0.001 = 1ms will give a tone of 1kHz +# Although not pitch perfect. + +[gcode_macro M300] +gcode: + # Use a default 1kHz tone if S is omitted. + {% set S = params.S|default(1000)|int %} + # Use a 10ms duration is P is omitted. + {% set P = params.P|default(100)|int %} + SET_PIN PIN=BEEPER_pin VALUE=0.5 CYCLE_TIME={ 1.0/S if S > 0 else 1 } + G4 P{P} + SET_PIN PIN=BEEPER_pin VALUE=0 + +[gcode_macro start_tones] +gcode: + M300 S1000 P500 ; chirp to indicate starting to print + +[gcode_macro end_tones] +gcode: + M300 S440 P200 ; Make Print Completed Tones + M300 S660 P250 + M300 S880 P300 + +[gcode_macro error_tones] +gcode: + M300 S700 P1500 ; Make Print Completed Tones + M300 S700 P500 ; Make Print Completed Tones + M300 S700 P500 ; Make Print Completed Tones + M300 S700 P500 ; Make Print Completed Tones + M300 S700 P500 ; Make Print Completed Tones + M300 S700 P500 ; Make Print Completed Tones + M300 S700 P500 ; Make Print Completed Tones + M300 S700 P500 ; Make Print Completed Tones + +[include fluidd.cfg] +[include leds.cfg] + +[include tones.cfg] + +[exclude_object] + +[virtual_sdcard] +path: /home/pi/printer_data/gcodes + +## Common Temperature Sensors +## "EPCOS 100K B57560G104F" +## "ATC Semitec 104GT-2" +## "NTC 100K beta 3950" +## "Honeywell 100K 135-104LAG-J01" +## "NTC 100K MGB18-104F39050L32" (Keenovo Heater Pad) +## "AD595" +## "PT100 INA826" +## "PT1000" + +#*# <---------------------- SAVE_CONFIG ----------------------> +#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated. +#*# +#*# [extruder] +#*# control = pid +#*# pid_kp = 26.862 +#*# pid_ki = 1.926 +#*# pid_kd = 93.682 +#*# +#*# [stepper_z] +#*# position_endstop = 1.640 +#*# +#*# [bed_mesh default] +#*# version = 1 +#*# points = +#*# 0.043750, 0.087500, 0.108750, 0.118750, 0.105000, 0.092500, 0.078750, 0.063750, 0.041250 +#*# 0.012500, 0.053750, 0.076250, 0.085000, 0.066250, 0.052500, 0.043750, 0.025000, 0.005000 +#*# -0.015000, 0.027500, 0.046250, 0.048750, 0.035000, 0.017500, 0.003750, -0.016250, -0.037500 +#*# -0.021250, 0.020000, 0.037500, 0.041250, 0.021250, 0.006250, -0.006250, -0.027500, -0.048750 +#*# -0.037500, -0.003750, 0.012500, 0.016250, 0.000000, -0.020000, -0.032500, -0.042500, -0.060000 +#*# -0.036250, -0.003750, 0.012500, 0.013750, -0.007500, -0.025000, -0.033750, -0.047500, -0.067500 +#*# -0.031250, -0.001250, 0.013750, 0.018750, 0.003750, -0.011250, -0.023750, -0.035000, -0.051250 +#*# -0.016250, 0.020000, 0.031250, 0.035000, 0.021250, 0.006250, -0.003750, -0.015000, -0.030000 +#*# 0.006250, 0.035000, 0.048750, 0.051250, 0.037500, 0.027500, 0.018750, 0.008750, -0.007500 +#*# tension = 0.2 +#*# min_x = 40.0 +#*# algo = bicubic +#*# y_count = 9 +#*# mesh_y_pps = 2 +#*# min_y = 40.0 +#*# x_count = 9 +#*# max_y = 260.0 +#*# mesh_x_pps = 2 +#*# max_x = 260.0 +#*# +#*# [probe] +#*# z_offset = -0.010 diff --git a/printer.cfg b/printer.cfg index cfbeb08..4c6075f 100644 --- a/printer.cfg +++ b/printer.cfg @@ -779,15 +779,15 @@ path: /home/pi/printer_data/gcodes #*# [bed_mesh default] #*# version = 1 #*# points = -#*# 0.043750, 0.087500, 0.108750, 0.118750, 0.105000, 0.092500, 0.078750, 0.063750, 0.041250 -#*# 0.012500, 0.053750, 0.076250, 0.085000, 0.066250, 0.052500, 0.043750, 0.025000, 0.005000 -#*# -0.015000, 0.027500, 0.046250, 0.048750, 0.035000, 0.017500, 0.003750, -0.016250, -0.037500 -#*# -0.021250, 0.020000, 0.037500, 0.041250, 0.021250, 0.006250, -0.006250, -0.027500, -0.048750 -#*# -0.037500, -0.003750, 0.012500, 0.016250, 0.000000, -0.020000, -0.032500, -0.042500, -0.060000 -#*# -0.036250, -0.003750, 0.012500, 0.013750, -0.007500, -0.025000, -0.033750, -0.047500, -0.067500 -#*# -0.031250, -0.001250, 0.013750, 0.018750, 0.003750, -0.011250, -0.023750, -0.035000, -0.051250 -#*# -0.016250, 0.020000, 0.031250, 0.035000, 0.021250, 0.006250, -0.003750, -0.015000, -0.030000 -#*# 0.006250, 0.035000, 0.048750, 0.051250, 0.037500, 0.027500, 0.018750, 0.008750, -0.007500 +#*# 0.013750, 0.062500, 0.090000, 0.111250, 0.098750, 0.098750, 0.095000, 0.103750, 0.107500 +#*# -0.017500, 0.030000, 0.053750, 0.075000, 0.076250, 0.063750, 0.066250, 0.053750, 0.047500 +#*# -0.047500, -0.003750, 0.017500, 0.030000, 0.032500, 0.037500, 0.030000, 0.001250, -0.002500 +#*# -0.056250, -0.011250, 0.011250, 0.018750, 0.021250, 0.055000, 0.040000, -0.003750, -0.010000 +#*# -0.068750, -0.028750, -0.005000, 0.008750, 0.000000, 0.002500, -0.000000, -0.011250, -0.017500 +#*# -0.048750, -0.003750, 0.010000, 0.020000, 0.021250, 0.018750, 0.007500, -0.001250, -0.010000 +#*# -0.031250, 0.003750, 0.017500, 0.028750, 0.035000, 0.038750, 0.023750, 0.020000, 0.016250 +#*# -0.006250, 0.028750, 0.045000, 0.057500, 0.053750, 0.046250, 0.042500, 0.045000, 0.037500 +#*# 0.002500, 0.038750, 0.063750, 0.072500, 0.071250, 0.067500, 0.065000, 0.067500, 0.060000 #*# tension = 0.2 #*# min_x = 40.0 #*# algo = bicubic