55 lines
1.6 KiB
Markdown
55 lines
1.6 KiB
Markdown
|
|
||
|
|
# Specs
|
||
|
|
|
||
|
|
High end compact shelf speakers
|
||
|
|
|
||
|
|
* Dimensions 35x20x34cm
|
||
|
|
* Wavecor WF146WA05 as the woofer
|
||
|
|
* Dynavox AMT-1 as the tweeter
|
||
|
|
* Crossover around 4kHz
|
||
|
|
* Power handling 55W
|
||
|
|
* Nominal impedance 4 ohm
|
||
|
|
|
||
|
|
Order kits from
|
||
|
|
http://www.lautsprecher-berlin-shop.de/epages/62721881.sf/de_DE/?ObjectPath=/Shops/62721881/Products/amt-box
|
||
|
|
|
||
|
|
NAD 3045 delivers just enough juice for these speakers.
|
||
|
|
|
||
|
|
# Enclosure
|
||
|
|
|
||
|
|
Generate toolpaths, following assumes 18mm plywood:
|
||
|
|
|
||
|
|
```bash
|
||
|
|
python3 enclosure.py --swap-axes --workpiece=front | tee amt-box-1-front.ngc amt-box-2-front.ngc
|
||
|
|
python3 enclosure.py --swap-axes --workpiece=side | tee amt-box-1-right.ngc amt-box-2-left.ngc
|
||
|
|
python3 enclosure.py --swap-axes --workpiece=back | tee amt-box-1-back.ngc amt-box-2-back.ngc
|
||
|
|
python3 enclosure.py --swap-axes --workpiece=cap | tee amt-box-1-top.ngc amt-box-1-bottom.ngc amt-box-2-top.ngc amt-box-2-bottom.ngc
|
||
|
|
python3 enclosure.py --swap-axes --workpiece=side --port-enable > amt-box-1-left.ngc
|
||
|
|
python3 enclosure.py --swap-axes --workpiece=side --port-enable --port-mirror > amt-box-2-right.ngc
|
||
|
|
python3 enclosure.py --workpiece=support | tee amt-box-1-support.ngc amt-box-2-support.ngc
|
||
|
|
```
|
||
|
|
|
||
|
|
Prepare approx 40cm by 90cm piece of plywood to accommodate following:
|
||
|
|
|
||
|
|
1. Mill support (8cm), this should leave enough room for clamps
|
||
|
|
2. Mill front (30cm)
|
||
|
|
3. Mill side (20cm)
|
||
|
|
4. Mill top (20cm)
|
||
|
|
|
||
|
|
Cut another 40 by 80cm piece:
|
||
|
|
|
||
|
|
5. Mill bottom (20cm), again this should leave enough room for clamps
|
||
|
|
6. Mill back (30cm)
|
||
|
|
7. Mill side (20cm)
|
||
|
|
|
||
|
|
Glue parts with wood glue (PVA).
|
||
|
|
Finish with
|
||
|
|
|
||
|
|
# Filter
|
||
|
|
|
||
|
|
Use single sided PCB, mill traces with the supplied circuit. Use possibly liquid tin to increase the
|
||
|
|
cross section of traces.
|
||
|
|
|
||
|
|
|
||
|
|
|