697 lines
18 KiB
INI
697 lines
18 KiB
INI
## Voron Design VORON2 250/300/350mm Spider TMC2209 UART config
|
|
|
|
## *** THINGS TO CHANGE/CHECK: ***
|
|
## MCU paths [mcu] section
|
|
## Thermistor types [extruder] and [heater_bed] sections - See 'sensor types' list at end of file
|
|
## Z Endstop Switch location [safe_z_home] section
|
|
## Homing end position [gcode_macro G32] section
|
|
## Z Endstop Switch offset for Z0 [stepper_z] section
|
|
## Probe points [quad_gantry_level] section
|
|
## Min & Max gantry corner postions [quad_gantry_level] section
|
|
## PID tune [extruder] and [heater_bed] sections
|
|
## Fine tune E steps [extruder] section
|
|
|
|
[mcu]
|
|
## Obtain definition by "ls -l /dev/serial/by-id/"
|
|
##--------------------------------------------------------------------
|
|
serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_420029001151383039343538-if00
|
|
|
|
## Uncomment below if you're using the Raspberry uart0 to communicate with Spider
|
|
#restart_method: command
|
|
|
|
[printer]
|
|
kinematics: corexy
|
|
max_velocity: 300
|
|
max_accel: 3000 #Max 4000
|
|
max_z_velocity: 15 #Max 15 for 12V TMC Drivers, can increase for 24V
|
|
max_z_accel: 350
|
|
square_corner_velocity: 5.0
|
|
|
|
#####################################################################
|
|
# X/Y Stepper Settings
|
|
#####################################################################
|
|
|
|
[stepper_x]
|
|
## Connected to X-MOT (B Motor)
|
|
step_pin: PE11
|
|
dir_pin: PE10
|
|
enable_pin: !PE9
|
|
rotation_distance: 40
|
|
microsteps: 32
|
|
full_steps_per_rotation:400 #set to 400 for 0.9 degree stepper
|
|
endstop_pin: ^PA1
|
|
position_min: 0
|
|
|
|
##--------------------------------------------------------------------
|
|
|
|
## Uncomment below for 250mm build
|
|
#position_endstop: 250
|
|
#position_max: 250
|
|
|
|
## Uncomment for 300mm build
|
|
position_endstop: 300
|
|
position_max: 300
|
|
|
|
# Uncomment for 350mm build
|
|
# position_endstop: 350
|
|
# position_max: 350
|
|
|
|
##--------------------------------------------------------------------
|
|
homing_speed: 100 #Max 100
|
|
homing_retract_dist: 5
|
|
homing_positive_dir: true
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_x]
|
|
uart_pin: PE7
|
|
interpolate: False
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
[stepper_y]
|
|
## Connected to Y-MOT (A Motor)
|
|
step_pin: PD8
|
|
dir_pin: PB12
|
|
enable_pin: !PD9
|
|
rotation_distance: 40
|
|
microsteps: 32
|
|
full_steps_per_rotation:400 #set to 400 for 0.9 degree stepper
|
|
endstop_pin: ^PA2
|
|
position_min: -10
|
|
##--------------------------------------------------------------------
|
|
|
|
## Uncomment for 250mm build
|
|
#position_endstop: 250
|
|
#position_max: 250
|
|
|
|
## Uncomment for 300mm build
|
|
position_endstop: 305
|
|
position_max: 305
|
|
|
|
# Uncomment for 350mm build
|
|
# position_endstop: 355
|
|
# position_max: 355
|
|
|
|
##--------------------------------------------------------------------
|
|
homing_speed: 100 #Max 100
|
|
homing_retract_dist: 5
|
|
homing_positive_dir: true
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_y]
|
|
uart_pin: PE15
|
|
interpolate: False
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
#####################################################################
|
|
# Z Stepper Settings
|
|
#####################################################################
|
|
|
|
## In Z-MOT Position
|
|
## Z0 Stepper - Front Left
|
|
[stepper_z]
|
|
step_pin: PD14
|
|
dir_pin: !PD13
|
|
enable_pin: !PD15
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 32
|
|
## In Z- Position
|
|
endstop_pin: ^PA0
|
|
## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0)
|
|
## (+) value = endstop above Z0, (-) value = endstop below
|
|
## Increasing position_endstop brings nozzle closer to the bed
|
|
## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config
|
|
#position_endstop: 0
|
|
##--------------------------------------------------------------------
|
|
|
|
## Uncomment below for 250mm build
|
|
#position_max: 230
|
|
|
|
## Uncomment below for 300mm build
|
|
position_max: 280
|
|
|
|
# # Uncomment below for 350mm build
|
|
# position_max: 295
|
|
|
|
##--------------------------------------------------------------------
|
|
position_min: -5
|
|
homing_speed: 8
|
|
second_homing_speed: 3
|
|
homing_retract_dist: 3
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_z]
|
|
uart_pin: PD10
|
|
interpolate: False
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
## In E1-MOT Position
|
|
## Z1 Stepper - Rear Left
|
|
[stepper_z1]
|
|
step_pin: PE6
|
|
dir_pin: PC13
|
|
enable_pin: !PE5
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 32
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_z1]
|
|
uart_pin: PC14
|
|
interpolate: False
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
## In E2-MOT Position
|
|
## Z2 Stepper - Rear Right
|
|
[stepper_z2]
|
|
step_pin: PE2
|
|
dir_pin: !PE4
|
|
enable_pin: !PE3
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 32
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_z2]
|
|
uart_pin: PC15
|
|
interpolate: False
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
## In E3-MOT Position
|
|
## Z3 Stepper - Front Right
|
|
[stepper_z3]
|
|
step_pin: PD12
|
|
dir_pin: PC4
|
|
enable_pin: !PE8
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 32
|
|
|
|
[tmc2209 stepper_z3]
|
|
uart_pin: PA15
|
|
interpolate: False
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
#######################################
|
|
#### Enclosure Temp Sensor Section ####
|
|
#######################################
|
|
# [thermistor chamber_temp]
|
|
# temperature1: 25
|
|
# resistance1: 10000
|
|
# beta: 3950
|
|
|
|
|
|
# [temperature_sensor enclosure_temp]
|
|
# sensor_type: chamber_temp
|
|
# sensor_pin: PC1
|
|
# min_temp: 0
|
|
# max_temp: 100
|
|
# gcode_id: C
|
|
|
|
#####################################################################
|
|
# Extruder
|
|
#####################################################################
|
|
|
|
## In E0-MOT Position
|
|
[extruder]
|
|
step_pin: PD5
|
|
dir_pin: !PD6
|
|
enable_pin: !PD4
|
|
|
|
## Update value below when you perform extruder calibration
|
|
## If you ask for 100mm of filament, but in reality it is 98mm:
|
|
## rotation_distance = <previous_rotation_distance> * <actual_extrude_distance> / 100
|
|
## 22.6789511 is a good starting point for Bondtech 5mm gears
|
|
## 34.37086 for Bondtech 8mm gears (Galileo)
|
|
rotation_distance: 22.90574
|
|
## Update Gear Ratio depending on your Extruder Type
|
|
## Use 50:17 for Afterburner/Clockwork (BMG Gear Ratio)
|
|
## Use 80:20 for M4, M3.1
|
|
## Use 7.5:1 for Galileo
|
|
|
|
gear_ratio: 50:10 #BMG Gear Ratio
|
|
microsteps: 32
|
|
full_steps_per_rotation: 200 #200 for 1.8 degree, 400 for 0.9 degree
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.75
|
|
## In E0 OUT Position
|
|
heater_pin: PB15
|
|
## Validate the following thermistor type to make sure it is correct
|
|
sensor_type: ATC Semitec 104NT-4-R025H42G
|
|
sensor_pin: PC0
|
|
min_temp: 10
|
|
max_temp: 270
|
|
max_power: 1.0
|
|
min_extrude_temp: 200
|
|
max_extrude_only_distance: 101
|
|
#control = pid
|
|
#pid_kp = 26.213
|
|
#pid_ki = 1.304
|
|
#pid_kd = 131.721
|
|
# Try to keep pressure_advance below 1.0
|
|
pressure_advance: 0.032
|
|
# Default is 0.040, leave stock
|
|
pressure_advance_smooth_time: 0.040
|
|
|
|
## In E0-MOT Position
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 extruder]
|
|
uart_pin: PD7
|
|
interpolate: false
|
|
run_current: 0.5
|
|
hold_current: 0.2
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
[filament_switch_sensor RunoutSensor]
|
|
pause_on_runout: False
|
|
runout_gcode: F_CONSUMED
|
|
switch_pin: ^PB13
|
|
event_delay: 4.0
|
|
|
|
[gcode_macro F_CONSUMED]
|
|
variable_filament_consumed: 0
|
|
variable_filament_lenght: 20 # length between the sensor and extruder
|
|
gcode:
|
|
# save current filament consumption
|
|
SET_GCODE_VARIABLE MACRO=F_CONSUMED VARIABLE=filament_consumed VALUE={printer.print_stats.filament_used}
|
|
# start checking filament consumption
|
|
UPDATE_DELAYED_GCODE ID=DELAY_M600 DURATION=1
|
|
|
|
[delayed_gcode DELAY_M600]
|
|
gcode:
|
|
# use set for easier reading
|
|
{% set consumed=printer["gcode_macro F_CONSUMED"].filament_consumed %}
|
|
{% set length=printer["gcode_macro F_CONSUMED"].filament_lenght %}
|
|
# check if predetermine length is reached
|
|
{% if printer.print_stats.filament_used|float <= (consumed|float + length|float) %}
|
|
# start looping this script every second
|
|
UPDATE_DELAYED_GCODE ID=DELAY_M600 DURATION=1
|
|
{% else %}
|
|
error_tones
|
|
PAUSE
|
|
{% endif %}
|
|
|
|
|
|
#####################################################################
|
|
# Bed Heater
|
|
#####################################################################
|
|
[heater_bed]
|
|
## SSR Pin - In BED OUT position
|
|
heater_pin: PC8
|
|
sensor_type: Generic 3950
|
|
sensor_pin: PB0 # TB Position
|
|
## Adjust Max Power so your heater doesn't warp your bed
|
|
max_power: 1
|
|
min_temp: 0
|
|
max_temp: 120
|
|
control: pid
|
|
pid_kp: 59.854
|
|
pid_ki: 1.596
|
|
pid_kd: 561.133
|
|
|
|
#####################################################################
|
|
# Probe
|
|
#####################################################################
|
|
|
|
[probe]
|
|
## This probe is not used for Z height, only Quad Gantry Leveling
|
|
## In Z+ position
|
|
## If your probe is NO instead of NC, change pin to ^!PA3
|
|
pin: ^PA3
|
|
x_offset: 0
|
|
y_offset: 25.0
|
|
z_offset: 0
|
|
speed: 10.0
|
|
samples: 3
|
|
samples_result: median
|
|
sample_retract_dist: 3.0
|
|
samples_tolerance: 0.006
|
|
samples_tolerance_retries: 3
|
|
|
|
#####################################################################
|
|
# Fan Control
|
|
#####################################################################
|
|
|
|
[heater_fan hotend_fan]
|
|
## Hotend Fan - FAN0 Connector
|
|
pin: PA13
|
|
max_power: 1.0
|
|
kick_start_time: 0.5
|
|
heater: extruder
|
|
heater_temp: 50.0
|
|
## If you are experiencing back flow, you can reduce fan_speed
|
|
#fan_speed: 1.0
|
|
|
|
[fan]
|
|
## Print Cooling Fan - FAN1 Connector
|
|
## Uncomment below for SpiderVersion 1.x
|
|
#pin: PB1
|
|
## Uncomment below for SpiderVersion 2.2
|
|
pin: PA14
|
|
max_power: 1
|
|
kick_start_time: 0.5
|
|
## Depending on your fan, you may need to increase this value
|
|
## if your fan will not start. Can change cycle_time (increase)
|
|
## if your fan is not able to slow down effectively
|
|
off_below: 0.10
|
|
|
|
[heater_fan controller_fan]
|
|
## Exhaust fan - In E2 OUT Positon
|
|
pin: PB3
|
|
max_power: 1.0
|
|
shutdown_speed: 0.0
|
|
kick_start_time: 5.0
|
|
heater: heater_bed
|
|
heater_temp: 60
|
|
fan_speed: 1.0
|
|
|
|
[heater_fan nevermore_fan]
|
|
# nevermore fan in fan3 connector
|
|
pin: PB2
|
|
max_power: 1.0
|
|
shutdown_speed: 0.0
|
|
kick_start_time: 5.0
|
|
heater: heater_bed
|
|
heater_temp: 60
|
|
fan_speed: 1.0
|
|
|
|
#####################################################################
|
|
# LED Control
|
|
#####################################################################
|
|
|
|
#[output_pin caselight ]
|
|
## Chamber Lighting - In E1 OUT Position
|
|
#pin: PC8
|
|
#pwm: true
|
|
#shutdown_value: 0
|
|
#cycle_time: 0.01
|
|
|
|
#####################################################################
|
|
# Homing and Gantry Adjustment Routines
|
|
#####################################################################
|
|
|
|
[idle_timeout]
|
|
timeout: 1800
|
|
|
|
[safe_z_home]
|
|
## XY Location of the Z Endstop Switch
|
|
## Update -10,-10 to the XY coordinates of your endstop pin
|
|
## (such as 157,305) after going through Z Endstop Pin
|
|
## Location Definition step.
|
|
home_xy_position:209,305
|
|
speed:100
|
|
z_hop:10
|
|
|
|
[quad_gantry_level]
|
|
## Use QUAD_GANTRY_LEVEL to level a gantry.
|
|
## Min & Max gantry corners - measure from nozzle at MIN (0,0) and
|
|
## MAX (250, 250), (300,300), or (350,350) depending on your printer size
|
|
## to respective belt positions
|
|
|
|
#--------------------------------------------------------------------
|
|
## Gantry Corners for 250mm Build
|
|
## Uncomment for 250mm build
|
|
#gantry_corners:
|
|
# -60,-10
|
|
# 310, 320
|
|
## Probe points
|
|
#points:
|
|
# 50,25
|
|
# 50,175
|
|
# 200,175
|
|
# 200,25
|
|
|
|
# Gantry Corners for 300mm Build
|
|
# Uncomment for 300mm build
|
|
gantry_corners:
|
|
-60,-10
|
|
360,370
|
|
# Probe points
|
|
points:
|
|
50,25
|
|
50,225
|
|
250,225
|
|
250,25
|
|
|
|
# # Gantry Corners for 350mm Build
|
|
# # Uncomment for 350mm build
|
|
# gantry_corners:
|
|
# -60,-10
|
|
# 410,420
|
|
# # Probe points
|
|
# points:
|
|
# 50,25
|
|
# 50,275
|
|
# 300,275
|
|
# 300,25
|
|
|
|
#--------------------------------------------------------------------
|
|
speed: 200
|
|
horizontal_move_z: 10
|
|
retries: 5
|
|
retry_tolerance: 0.0075
|
|
max_adjust: 10
|
|
|
|
|
|
[bed_mesh]
|
|
speed: 300
|
|
horizontal_move_z: 10
|
|
##--------------------------------------------------------------------
|
|
## Uncomment below for 250mm build
|
|
#mesh_min: 40, 40
|
|
#mesh_max: 210,210
|
|
|
|
# Uncomment for 300mm build
|
|
mesh_min: 40, 40
|
|
mesh_max: 260,260
|
|
zero_reference_position: 150,150
|
|
|
|
# # Uncomment for 350mm build
|
|
# mesh_min: 40, 40
|
|
# mesh_max: 310,310
|
|
##--------------------------------------------------------------------
|
|
fade_start: 0.6
|
|
fade_end: 10.0
|
|
probe_count: 9,9
|
|
algorithm: bicubic
|
|
#relative_reference_index: 40
|
|
|
|
#####################################################################
|
|
# Displays
|
|
#####################################################################
|
|
|
|
#--------------------------------------------------------------------
|
|
|
|
[display]
|
|
# mini12864 LCD Display
|
|
lcd_type: uc1701
|
|
cs_pin: PC11
|
|
a0_pin: PD2
|
|
rst_pin: PC10
|
|
encoder_pins: ^PC6,^PC7
|
|
click_pin: ^!PA8
|
|
contrast: 63
|
|
#spi_bus: spi1
|
|
spi_software_mosi_pin: PA7
|
|
spi_software_miso_pin: PA6
|
|
spi_software_sclk_pin: PA5
|
|
|
|
[neopixel fysetc_mini12864]
|
|
# To control Neopixel RGB in mini12864 display
|
|
pin: PC12
|
|
chain_count: 3
|
|
initial_RED: 0.1
|
|
initial_GREEN: 0.5
|
|
initial_BLUE: 0.0
|
|
color_order: RGB
|
|
|
|
# Set RGB values on boot up for each Neopixel.
|
|
# Index 1 = display, Index 2 and 3 = Knob
|
|
[delayed_gcode setdisplayneopixel]
|
|
initial_duration: 1
|
|
gcode:
|
|
SET_LED LED=fysetc_mini12864 RED=1 GREEN=1 BLUE=1 INDEX=1 TRANSMIT=0
|
|
SET_LED LED=fysetc_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=2 TRANSMIT=0
|
|
SET_LED LED=fysetc_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=3
|
|
|
|
#--------------------------------------------------------------------
|
|
|
|
|
|
#####################################################################
|
|
# Macros
|
|
#####################################################################
|
|
|
|
[gcode_macro CENTER]
|
|
gcode:
|
|
G0 X150 Y150 Z30 F3600
|
|
|
|
[gcode_macro G32]
|
|
gcode:
|
|
SAVE_GCODE_STATE NAME=STATE_G32
|
|
G90
|
|
G28
|
|
QUAD_GANTRY_LEVEL
|
|
G28
|
|
|
|
## Uncomment for for your size printer:
|
|
#--------------------------------------------------------------------
|
|
## Uncomment for 250mm build
|
|
#G0 X125 Y125 Z30 F3600
|
|
|
|
## Uncomment for 300 build
|
|
G0 X150 Y150 Z30 F3600
|
|
|
|
## Uncomment for 350mm build
|
|
# G0 X175 Y175 Z30 F3600
|
|
#--------------------------------------------------------------------
|
|
RESTORE_GCODE_STATE NAME=STATE_G32
|
|
|
|
|
|
[gcode_macro PRINT_START]
|
|
# Use PRINT_START for the slicer starting script - please customise for your slicer of choice
|
|
gcode:
|
|
start_tones
|
|
BED_MESH_CLEAR
|
|
G32 ; home all axes
|
|
BED_MESH_PROFILE LOAD=default
|
|
G90
|
|
G0 X175 Y175 Z30 F3600 ; move nozzle away from bed
|
|
status_printing
|
|
|
|
[gcode_macro PRINT_END]
|
|
# Use PRINT_END for the slicer ending script - please customise for your slicer of choice
|
|
gcode:
|
|
M400 ; wait for buffer to clear
|
|
G92 E0 ; zero the extruder
|
|
G1 E-5 F1800 ; retract filament
|
|
G91 ; relative positioning
|
|
G0 Z1.00 X20.0 Y20.0 F20000 ; move nozzle to remove stringing
|
|
TURN_OFF_HEATERS
|
|
M107 ; turn off fan
|
|
G1 Z2 F3000 ; move nozzle up 2mm
|
|
G90 ; absolute positioning
|
|
G0 X125 Y250 F3600 ; park nozzle at rear
|
|
BED_MESH_CLEAR
|
|
end_tones
|
|
|
|
|
|
|
|
######################################################################
|
|
# Beeper
|
|
######################################################################
|
|
|
|
# M300 : Play tone. Beeper support, as commonly found on usual LCD
|
|
# displays (i.e. RepRapDiscount 2004 Smart Controller, RepRapDiscount
|
|
# 12864 Full Graphic). This defines a custom I/O pin and a custom
|
|
# GCODE macro. Usage:
|
|
# M300 [P<ms>] [S<Hz>]
|
|
# P is the tone duration, S the tone frequency.
|
|
# The frequency won't be pitch perfect.
|
|
|
|
[output_pin BEEPER_pin]
|
|
pin: PC9
|
|
# Beeper pin. This parameter must be provided.
|
|
# ar37 is the default RAMPS/MKS pin.
|
|
pwm: True
|
|
# A piezo beeper needs a PWM signal, a DC buzzer doesn't.
|
|
value: 0
|
|
# Silent at power on, set to 1 if active low.
|
|
shutdown_value: 0
|
|
# Disable at emergency shutdown (no PWM would be available anyway).
|
|
cycle_time: 0.001
|
|
# Default PWM frequency : 0.001 = 1ms will give a tone of 1kHz
|
|
# Although not pitch perfect.
|
|
|
|
[gcode_macro M300]
|
|
gcode:
|
|
# Use a default 1kHz tone if S is omitted.
|
|
{% set S = params.S|default(1000)|int %}
|
|
# Use a 10ms duration is P is omitted.
|
|
{% set P = params.P|default(100)|int %}
|
|
SET_PIN PIN=BEEPER_pin VALUE=0.5 CYCLE_TIME={ 1.0/S if S > 0 else 1 }
|
|
G4 P{P}
|
|
SET_PIN PIN=BEEPER_pin VALUE=0
|
|
|
|
[gcode_macro start_tones]
|
|
gcode:
|
|
M300 S1000 P500 ; chirp to indicate starting to print
|
|
|
|
[gcode_macro end_tones]
|
|
gcode:
|
|
M300 S440 P200 ; Make Print Completed Tones
|
|
M300 S660 P250
|
|
M300 S880 P300
|
|
|
|
[gcode_macro error_tones]
|
|
gcode:
|
|
M300 S700 P1500 ; Make Print Completed Tones
|
|
M300 S700 P500 ; Make Print Completed Tones
|
|
M300 S700 P500 ; Make Print Completed Tones
|
|
M300 S700 P500 ; Make Print Completed Tones
|
|
M300 S700 P500 ; Make Print Completed Tones
|
|
M300 S700 P500 ; Make Print Completed Tones
|
|
M300 S700 P500 ; Make Print Completed Tones
|
|
M300 S700 P500 ; Make Print Completed Tones
|
|
|
|
[include fluidd.cfg]
|
|
[include leds.cfg]
|
|
|
|
|
|
## Common Temperature Sensors
|
|
## "EPCOS 100K B57560G104F"
|
|
## "ATC Semitec 104GT-2"
|
|
## "NTC 100K beta 3950"
|
|
## "Honeywell 100K 135-104LAG-J01"
|
|
## "NTC 100K MGB18-104F39050L32" (Keenovo Heater Pad)
|
|
## "AD595"
|
|
## "PT100 INA826"
|
|
## "PT1000"
|
|
|
|
#*# <---------------------- SAVE_CONFIG ---------------------->
|
|
#*# DO NOT EDIT THIS BLOCK OR BELOW. The contents are auto-generated.
|
|
#*#
|
|
#*# [extruder]
|
|
#*# control = pid
|
|
#*# pid_kp = 26.862
|
|
#*# pid_ki = 1.926
|
|
#*# pid_kd = 93.682
|
|
#*#
|
|
#*# [stepper_z]
|
|
#*# position_endstop = 1.640
|
|
#*#
|
|
#*# [bed_mesh default]
|
|
#*# version = 1
|
|
#*# points =
|
|
#*# 0.035000, 0.082500, 0.100000, 0.110000, 0.095000, 0.081250, 0.067500, 0.053750, 0.031250
|
|
#*# 0.003750, 0.046250, 0.066250, 0.075000, 0.058750, 0.042500, 0.030000, 0.010000, -0.011250
|
|
#*# -0.015000, 0.026250, 0.047500, 0.046250, 0.028750, 0.007500, -0.006250, -0.022500, -0.048750
|
|
#*# -0.022500, 0.017500, 0.031250, 0.032500, 0.012500, -0.006250, -0.020000, -0.041250, -0.068750
|
|
#*# -0.030000, 0.005000, 0.015000, 0.016250, 0.000000, -0.018750, -0.036250, -0.053750, -0.076250
|
|
#*# -0.026250, 0.005000, 0.013750, 0.013750, -0.006250, -0.025000, -0.041250, -0.060000, -0.083750
|
|
#*# -0.006250, 0.021250, 0.031250, 0.030000, 0.011250, -0.006250, -0.021250, -0.037500, -0.063750
|
|
#*# 0.011250, 0.042500, 0.051250, 0.051250, 0.032500, 0.011250, -0.001250, -0.016250, -0.037500
|
|
#*# 0.040000, 0.063750, 0.076250, 0.075000, 0.055000, 0.037500, 0.021250, 0.005000, -0.011250
|
|
#*# tension = 0.2
|
|
#*# min_x = 40.0
|
|
#*# algo = bicubic
|
|
#*# y_count = 9
|
|
#*# mesh_y_pps = 2
|
|
#*# min_y = 40.0
|
|
#*# x_count = 9
|
|
#*# max_y = 260.0
|
|
#*# mesh_x_pps = 2
|
|
#*# max_x = 260.0
|