549 lines
14 KiB
INI
549 lines
14 KiB
INI
## Voron Design VORON 2.4R2 250/300/350mm with Spider config, Lecktor kit
|
|
|
|
## *** THINGS TO CHANGE/CHECK: ***
|
|
## MCU paths [mcu] section
|
|
## Thermistor types [extruder] and [heater_bed] sections - See 'sensor types' list at end of file
|
|
## Z Endstop Switch location [safe_z_home] section
|
|
## Homing end position [gcode_macro G32] section
|
|
## Z Endstop Switch offset for Z0 [stepper_z] section
|
|
## Probe points [quad_gantry_level] section
|
|
## Min & Max gantry corner postions [quad_gantry_level] section
|
|
## PID tune [extruder] and [heater_bed] sections
|
|
## Fine tune E steps [extruder] section
|
|
|
|
## *** FOR REFERENCE ***
|
|
##
|
|
## ^PA1 - X endstop
|
|
## ^PA2 - Y endstop
|
|
## ^PA3 - proximity probe
|
|
## ^PB14 - unused
|
|
## PB13 - Case Leds
|
|
## ^PA0 - Z-endstop
|
|
## PB0 - Bed thermistor
|
|
## PC0 - Hot-End thermistor
|
|
## PA13 - EFAN
|
|
## PA14 - PFAN
|
|
## PB2 - Nevermore fans
|
|
##
|
|
|
|
[mcu]
|
|
## Obtain definition by "ls -l /dev/serial/by-id/"
|
|
##--------------------------------------------------------------------
|
|
serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_3E0019000F51383039343538-if00
|
|
|
|
## Uncomment below if you're using the Raspberry uart0 to communicate with Spider
|
|
#restart_method: command
|
|
|
|
[printer]
|
|
kinematics: corexy
|
|
max_velocity: 300
|
|
max_accel: 3000 #Max 4000
|
|
max_z_velocity: 15 #Max 15 for 12V TMC Drivers, can increase for 24V
|
|
max_z_accel: 350
|
|
square_corner_velocity: 5.0
|
|
|
|
#####################################################################
|
|
# X/Y Stepper Settings
|
|
#####################################################################
|
|
|
|
[stepper_x]
|
|
## Connected to X-MOT (B Motor)
|
|
step_pin: PE11
|
|
dir_pin: PE10
|
|
enable_pin: !PE9
|
|
rotation_distance: 40
|
|
microsteps: 32
|
|
full_steps_per_rotation:400 #set to 400 for 0.9 degree stepper
|
|
endstop_pin: ^PA1
|
|
position_min: 0
|
|
|
|
##--------------------------------------------------------------------
|
|
|
|
## Uncomment below for 250mm build
|
|
#position_endstop: 250
|
|
#position_max: 250
|
|
|
|
## Uncomment for 300mm build
|
|
#position_endstop: 300
|
|
#position_max: 300
|
|
|
|
# Uncomment for 350mm build
|
|
position_endstop: 350
|
|
position_max: 350
|
|
|
|
##--------------------------------------------------------------------
|
|
homing_speed: 100 #Max 100
|
|
homing_retract_dist: 5
|
|
homing_positive_dir: true
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_x]
|
|
uart_pin: PE7
|
|
interpolate: False
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
[stepper_y]
|
|
## Connected to Y-MOT (A Motor)
|
|
step_pin: PD8
|
|
dir_pin: PB12
|
|
enable_pin: !PD9
|
|
rotation_distance: 40
|
|
microsteps: 32
|
|
full_steps_per_rotation:400 #set to 400 for 0.9 degree stepper
|
|
endstop_pin: ^PA2
|
|
position_min: -10
|
|
##--------------------------------------------------------------------
|
|
|
|
## Uncomment for 250mm build
|
|
#position_endstop: 250
|
|
#position_max: 250
|
|
|
|
## Uncomment for 300mm build
|
|
#position_endstop: 300
|
|
#position_max: 300
|
|
|
|
# Uncomment for 350mm build
|
|
position_endstop: 355
|
|
position_max: 355
|
|
|
|
##--------------------------------------------------------------------
|
|
homing_speed: 100 #Max 100
|
|
homing_retract_dist: 5
|
|
homing_positive_dir: true
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_y]
|
|
uart_pin: PE15
|
|
interpolate: False
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
#####################################################################
|
|
# Z Stepper Settings
|
|
#####################################################################
|
|
|
|
## In Z-MOT Position
|
|
## Z0 Stepper - Front Left
|
|
[stepper_z]
|
|
step_pin: PD14
|
|
dir_pin: !PD13
|
|
enable_pin: !PD15
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 32
|
|
## In Z- Position
|
|
endstop_pin: ^PA0
|
|
## Z-position of nozzle (in mm) to z-endstop trigger point relative to print surface (Z0)
|
|
## (+) value = endstop above Z0, (-) value = endstop below
|
|
## Increasing position_endstop brings nozzle closer to the bed
|
|
## After you run Z_ENDSTOP_CALIBRATE, position_endstop will be stored at the very end of your config
|
|
position_endstop: 0
|
|
##--------------------------------------------------------------------
|
|
|
|
## Uncomment below for 250mm build
|
|
#position_max: 230
|
|
|
|
## Uncomment below for 300mm build
|
|
#position_max: 280
|
|
|
|
# Uncomment below for 350mm build
|
|
position_max: 295
|
|
|
|
##--------------------------------------------------------------------
|
|
position_min: -5
|
|
homing_speed: 8
|
|
second_homing_speed: 3
|
|
homing_retract_dist: 3
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_z]
|
|
uart_pin: PD10
|
|
interpolate: False
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
## In E1-MOT Position
|
|
## Z1 Stepper - Rear Left
|
|
[stepper_z1]
|
|
step_pin: PE6
|
|
dir_pin: PC13
|
|
enable_pin: !PE5
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 32
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_z1]
|
|
uart_pin: PC14
|
|
interpolate: False
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
## In E2-MOT Position
|
|
## Z2 Stepper - Rear Right
|
|
[stepper_z2]
|
|
step_pin: PE2
|
|
dir_pin: !PE4
|
|
enable_pin: !PE3
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 32
|
|
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 stepper_z2]
|
|
uart_pin: PC15
|
|
interpolate: False
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
## In E3-MOT Position
|
|
## Z3 Stepper - Front Right
|
|
[stepper_z3]
|
|
step_pin: PD12
|
|
dir_pin: PC4
|
|
enable_pin: !PE8
|
|
rotation_distance: 40
|
|
gear_ratio: 80:16
|
|
microsteps: 32
|
|
|
|
[tmc2209 stepper_z3]
|
|
uart_pin: PA15
|
|
interpolate: False
|
|
run_current: 0.8
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
#######################################
|
|
#### Enclosure Temp Sensor Section ####
|
|
#######################################
|
|
##[thermistor chamber_temp]
|
|
##temperature1: 25
|
|
##resistance1: 10000
|
|
##beta: 3950
|
|
|
|
|
|
##[temperature_sensor enclosure_temp]
|
|
##sensor_type: chamber_temp
|
|
##sensor_pin: PC1
|
|
##min_temp: 0
|
|
##max_temp: 100
|
|
##gcode_id: C
|
|
|
|
#####################################################################
|
|
# Extruder
|
|
#####################################################################
|
|
|
|
## In E0-MOT Position
|
|
[extruder]
|
|
step_pin: PD5
|
|
dir_pin: !PD6
|
|
enable_pin: !PD4
|
|
|
|
## Update value below when you perform extruder calibration
|
|
## If you ask for 100mm of filament, but in reality it is 98mm:
|
|
## rotation_distance = <previous_rotation_distance> * <actual_extrude_distance> / 100
|
|
## 22.6789511 is a good starting point for Bondtech 5mm gears
|
|
## 34.37086 for Bondtech 8mm gears (Galileo)
|
|
## 22.90574 # for Bondtech on afterburner
|
|
## 22.7923459 # for Bondtech on stealthburner
|
|
rotation_distance: 22.7923459 # CALIBRATED for Stealthburner
|
|
## Update Gear Ratio depending on your Extruder Type
|
|
## Use 50:17 for Afterburner/Clockwork (BMG Gear Ratio)
|
|
## Use 80:20 for M4, M3.1
|
|
## Use 7.5:1 for Galileo
|
|
gear_ratio: 5:1 #for Galileo
|
|
microsteps: 32
|
|
full_steps_per_rotation: 200 #200 for 1.8 degree, 400 for 0.9 degree
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.75
|
|
## In E0 OUT Position
|
|
heater_pin: PB15
|
|
## Validate the following thermistor type to make sure it is correct
|
|
sensor_type: ATC Semitec 104NT-4-R025H42G
|
|
sensor_pin: PC0
|
|
min_temp: 10
|
|
max_temp: 270
|
|
max_power: 1.0
|
|
min_extrude_temp: 180
|
|
control = pid
|
|
pid_kp = 26.213
|
|
pid_ki = 1.304
|
|
pid_kd = 131.721
|
|
# Try to keep pressure_advance below 1.0
|
|
pressure_advance: 0.05
|
|
# Default is 0.040, leave stock
|
|
pressure_advance_smooth_time: 0.040
|
|
|
|
## In E0-MOT Position
|
|
## Make sure to update below for your relevant driver (2208 or 2209)
|
|
[tmc2209 extruder]
|
|
uart_pin: PD7
|
|
interpolate: false
|
|
run_current: 0.5
|
|
hold_current: 0.2
|
|
sense_resistor: 0.110
|
|
stealthchop_threshold: 0
|
|
|
|
##[filament_switch_sensor RunoutSensor]
|
|
##pause_on_runout: False
|
|
##runout_gcode: F_CONSUMED
|
|
##switch_pin: ^PB13
|
|
##event_delay: 4.0##
|
|
|
|
##[gcode_macro F_CONSUMED]
|
|
##variable_filament_consumed: 0
|
|
##variable_filament_lenght: 20 # length between the sensor and extruder
|
|
##gcode:
|
|
## # save current filament consumption
|
|
## SET_GCODE_VARIABLE MACRO=F_CONSUMED VARIABLE=filament_consumed VALUE={printer.print_stats.filament_used}
|
|
## # start checking filament consumption
|
|
## UPDATE_DELAYED_GCODE ID=DELAY_M600 DURATION=1##
|
|
|
|
##[delayed_gcode DELAY_M600]
|
|
##gcode:
|
|
## # use set for easier reading
|
|
## {% set consumed=printer["gcode_macro F_CONSUMED"].filament_consumed %}
|
|
## {% set length=printer["gcode_macro F_CONSUMED"].filament_lenght %}
|
|
## # check if predetermine length is reached
|
|
## {% if printer.print_stats.filament_used|float <= (consumed|float + length|float) %}
|
|
## # start looping this script every second
|
|
## UPDATE_DELAYED_GCODE ID=DELAY_M600 DURATION=1
|
|
## {% else %}
|
|
## error_tones
|
|
## PAUSE
|
|
## {% endif %}
|
|
|
|
|
|
#####################################################################
|
|
# Bed Heater
|
|
#####################################################################
|
|
[heater_bed]
|
|
## SSR Pin - In BED OUT position
|
|
heater_pin: PC8
|
|
sensor_type: Generic 3950
|
|
sensor_pin: PB0 # TB Position
|
|
## Adjust Max Power so your heater doesn't warp your bed
|
|
max_power: 0.6
|
|
min_temp: 0
|
|
max_temp: 120
|
|
control: pid
|
|
pid_kp: 59.854
|
|
pid_ki: 1.596
|
|
pid_kd: 561.133
|
|
|
|
#####################################################################
|
|
# Probe
|
|
#####################################################################
|
|
|
|
[probe]
|
|
## This probe is not used for Z height, only Quad Gantry Leveling
|
|
## In Z+ position
|
|
## If your probe is NO instead of NC, change pin to ^!PA3
|
|
pin: ^PA3
|
|
x_offset: 0
|
|
y_offset: 25.0
|
|
z_offset: 0
|
|
speed: 10.0
|
|
samples: 3
|
|
samples_result: median
|
|
sample_retract_dist: 3.0
|
|
samples_tolerance: 0.006
|
|
samples_tolerance_retries: 3
|
|
|
|
#####################################################################
|
|
# Fan Control
|
|
#####################################################################
|
|
|
|
[heater_fan hotend_fan]
|
|
## Hotend Fan - FAN0 Connector
|
|
pin: PA13
|
|
max_power: 1.0
|
|
kick_start_time: 0.5
|
|
heater: extruder
|
|
heater_temp: 50.0
|
|
## If you are experiencing back flow, you can reduce fan_speed
|
|
#fan_speed: 1.0
|
|
|
|
[fan]
|
|
## Print Cooling Fan - FAN1 Connector
|
|
## Uncomment below for SpiderVersion 1.x
|
|
#pin: PB1
|
|
## Uncomment below for SpiderVersion 2.2
|
|
pin: PA14
|
|
max_power: 1
|
|
kick_start_time: 0.5
|
|
## Depending on your fan, you may need to increase this value
|
|
## if your fan will not start. Can change cycle_time (increase)
|
|
## if your fan is not able to slow down effectively
|
|
off_below: 0.10
|
|
|
|
[heater_fan controller_fan]
|
|
## Exhaust fan - In E2 OUT Positon
|
|
pin: PB3
|
|
max_power: 1
|
|
shutdown_speed: 0.0
|
|
kick_start_time: 5.0
|
|
heater: heater_bed
|
|
heater_temp: 60
|
|
fan_speed: 1.0
|
|
|
|
[heater_fan nevermore_fan]
|
|
# nevermore fan in fan3 connector
|
|
pin: PB2
|
|
max_power: 0.8
|
|
shutdown_speed: 0.0
|
|
kick_start_time: 5.0
|
|
heater: heater_bed
|
|
heater_temp: 60
|
|
fan_speed: 1.0
|
|
|
|
#####################################################################
|
|
# Homing and Gantry Adjustment Routines
|
|
#####################################################################
|
|
|
|
[idle_timeout]
|
|
timeout: 9000
|
|
|
|
[safe_z_home]
|
|
## XY Location of the Z Endstop Switch
|
|
## Update -10,-10 to the XY coordinates of your endstop pin
|
|
## (such as 157,305) after going through Z Endstop Pin
|
|
## Location Definition step.
|
|
home_xy_position:231,355
|
|
speed:100
|
|
z_hop:10
|
|
|
|
[quad_gantry_level]
|
|
## Use QUAD_GANTRY_LEVEL to level a gantry.
|
|
## Min & Max gantry corners - measure from nozzle at MIN (0,0) and
|
|
## MAX (250, 250), (300,300), or (350,350) depending on your printer size
|
|
## to respective belt positions
|
|
|
|
#--------------------------------------------------------------------
|
|
## Gantry Corners for 250mm Build
|
|
## Uncomment for 250mm build
|
|
#gantry_corners:
|
|
# -60,-10
|
|
# 310, 320
|
|
## Probe points
|
|
#points:
|
|
# 50,25
|
|
# 50,175
|
|
# 200,175
|
|
# 200,25
|
|
|
|
## Gantry Corners for 300mm Build
|
|
## Uncomment for 300mm build
|
|
#gantry_corners:
|
|
# -60,-10
|
|
# 360,370
|
|
## Probe points
|
|
#points:
|
|
# 50,25
|
|
# 50,225
|
|
# 250,225
|
|
# 250,25
|
|
|
|
# Gantry Corners for 350mm Build
|
|
# Uncomment for 350mm build
|
|
gantry_corners:
|
|
-60,-10
|
|
410,420
|
|
# Probe points
|
|
points:
|
|
50,25
|
|
50,275
|
|
300,275
|
|
300,25
|
|
|
|
#--------------------------------------------------------------------
|
|
speed: 200
|
|
horizontal_move_z: 10
|
|
retries: 5
|
|
retry_tolerance: 0.0075
|
|
max_adjust: 10
|
|
|
|
|
|
[bed_mesh]
|
|
speed: 300
|
|
horizontal_move_z: 10
|
|
##--------------------------------------------------------------------
|
|
## Uncomment below for 250mm build
|
|
#mesh_min: 40, 40
|
|
#mesh_max: 210,210
|
|
|
|
## Uncomment for 300mm build
|
|
#mesh_min: 40, 40
|
|
#mesh_max: 260,260
|
|
|
|
# Uncomment for 350mm build
|
|
mesh_min: 40, 40
|
|
mesh_max: 310,310
|
|
##--------------------------------------------------------------------
|
|
fade_start: 0.6
|
|
fade_end: 10.0
|
|
probe_count: 9,9
|
|
algorithm: bicubic
|
|
relative_reference_index: 40
|
|
|
|
#####################################################################
|
|
# Displays
|
|
#####################################################################
|
|
|
|
#--------------------------------------------------------------------
|
|
|
|
[display]
|
|
# mini12864 LCD Display
|
|
lcd_type: uc1701
|
|
cs_pin: PC11
|
|
a0_pin: PD2
|
|
rst_pin: PC10
|
|
encoder_pins: ^PC6,^PC7
|
|
click_pin: ^!PA8
|
|
contrast: 63
|
|
#spi_bus: spi1
|
|
spi_software_mosi_pin: PA7
|
|
spi_software_miso_pin: PA6
|
|
spi_software_sclk_pin: PA5
|
|
|
|
[neopixel fysetc_mini12864]
|
|
# To control Neopixel RGB in mini12864 display
|
|
pin: PC12
|
|
chain_count: 3
|
|
initial_RED: 0.1
|
|
initial_GREEN: 0.5
|
|
initial_BLUE: 0.0
|
|
color_order: RGB
|
|
|
|
# Set RGB values on boot up for each Neopixel.
|
|
# Index 1 = display, Index 2 and 3 = Knob
|
|
[delayed_gcode setdisplayneopixel]
|
|
initial_duration: 1
|
|
gcode:
|
|
SET_LED LED=fysetc_mini12864 RED=1 GREEN=1 BLUE=1 INDEX=1 TRANSMIT=0
|
|
SET_LED LED=fysetc_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=2 TRANSMIT=0
|
|
SET_LED LED=fysetc_mini12864 RED=1 GREEN=0 BLUE=0 INDEX=3
|
|
|
|
#--------------------------------------------------------------------
|
|
|
|
[include mainsail.cfg]
|
|
[include menu_bed.cfg]
|
|
[include leds.cfg]
|
|
[include stealthburner_leds.cfg]
|
|
[include macros.cfg]
|
|
|
|
## Common Temperature Sensors
|
|
## "EPCOS 100K B57560G104F"
|
|
## "ATC Semitec 104GT-2"
|
|
## "NTC 100K beta 3950"
|
|
## "Honeywell 100K 135-104LAG-J01"
|
|
## "NTC 100K MGB18-104F39050L32" (Keenovo Heater Pad)
|
|
## "AD595"
|
|
## "PT100 INA826"
|
|
## "PT1000" |