updates config to match latest kits

Manuals/Klipper/Mainsail/printer.cfg

@@ -1,4 +1,4 @@
-## Voron Design VORON2 250/300/350mm Spider TMC2209 UART config
+## Voron Design VORON 2.4R2 250/300/350mm with Spider config, Lecktor kit
 
 ## *** THINGS TO CHANGE/CHECK: ***
 ## MCU paths							        [mcu] section
@@ -29,7 +29,7 @@
 [mcu]
 ##	Obtain definition by "ls -l /dev/serial/by-id/" 
 ##--------------------------------------------------------------------
-serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_3E0019000F51383039343538-if00
+serial: /dev/serial/by-id/usb-Klipper_stm32f446xx_2B002A001151383039343538-if00
 
 ## Uncomment below if you're using the Raspberry uart0 to communicate with Spider
 #restart_method: command
@@ -49,7 +49,7 @@ square_corner_velocity: 5.0
 [stepper_x]
 ##	Connected to X-MOT (B Motor)
 step_pin: PE11
-dir_pin: !PE10
+dir_pin: PE10
 enable_pin: !PE9
 rotation_distance: 40
 microsteps: 32
@@ -87,7 +87,7 @@ stealthchop_threshold: 0
 [stepper_y]
 ##	Connected to Y-MOT (A Motor)
 step_pin: PD8
-dir_pin: !PB12
+dir_pin: PB12
 enable_pin: !PD9
 rotation_distance: 40
 microsteps: 32
@@ -250,12 +250,14 @@ enable_pin: !PD4
 ##	rotation_distance = <previous_rotation_distance> * <actual_extrude_distance> / 100
 ##  22.6789511 is a good starting point for Bondtech 5mm gears
 ##  34.37086 for Bondtech 8mm gears (Galileo)
-rotation_distance: 22.90574 # CALIBRATED !	
+##  22.90574 # for Bondtech on afterburner
+##  22.7923459 # for Bondtech on stealthburner
+rotation_distance: 22.7923459 # CALIBRATED for Stealthburner
 ##	Update Gear Ratio depending on your Extruder Type
 ##	Use 50:17 for Afterburner/Clockwork (BMG Gear Ratio)
 ##	Use 80:20 for M4, M3.1
 ##  Use 7.5:1 for Galileo
-gear_ratio: 50:17				#BMG Gear Ratio
+gear_ratio: 50:1				#for Galileo
 microsteps: 32
 full_steps_per_rotation: 200	#200 for 1.8 degree, 400 for 0.9 degree
 nozzle_diameter: 0.400
@@ -268,11 +270,11 @@ sensor_pin: PC0
 min_temp: 10
 max_temp: 270
 max_power: 1.0
-min_extrude_temp: 190
-#control = pid
-#pid_kp = 26.213
-#pid_ki = 1.304
-#pid_kd = 131.721
+min_extrude_temp: 180
+control = pid
+pid_kp = 26.213
+pid_ki = 1.304
+pid_kd = 131.721
 #	Try to keep pressure_advance below 1.0
 pressure_advance: 0.05
 #	Default is 0.040, leave stock
@@ -289,14 +291,33 @@ sense_resistor: 0.110
 stealthchop_threshold: 0
 
 ##[filament_switch_sensor RunoutSensor]
-##pause_on_runout: True
-##runout_gcode:  
-##    M117 FILAMENT RUNOUT
-##    error_tones
-##insert_gcode:
-##    M117 FILAMENT OK
+##pause_on_runout: False
+##runout_gcode:  F_CONSUMED
 ##switch_pin: ^PB13
-##event_delay: 5.0
+##event_delay: 4.0##
+
+##[gcode_macro F_CONSUMED]
+##variable_filament_consumed: 0
+##variable_filament_lenght: 20   # length between the sensor and extruder
+##gcode:
+##    # save current filament consumption
+##    SET_GCODE_VARIABLE MACRO=F_CONSUMED VARIABLE=filament_consumed VALUE={printer.print_stats.filament_used}
+##    # start checking filament consumption
+##    UPDATE_DELAYED_GCODE ID=DELAY_M600 DURATION=1##
+
+##[delayed_gcode DELAY_M600]
+##gcode:
+##    # use set for easier reading
+##    {% set consumed=printer["gcode_macro F_CONSUMED"].filament_consumed %}
+##    {% set length=printer["gcode_macro F_CONSUMED"].filament_lenght %}
+##    # check if predetermine length is reached
+##    {% if printer.print_stats.filament_used|float <= (consumed|float + length|float) %}
+##    # start looping this script every second
+##    UPDATE_DELAYED_GCODE ID=DELAY_M600 DURATION=1
+##    {% else %}
+##    error_tones
+##    PAUSE
+##    {% endif %}
 
 
 #####################################################################
@@ -365,7 +386,7 @@ off_below: 0.10
 [heater_fan controller_fan]
 ##	Exhaust fan - In E2 OUT Positon
 pin: PB3
-max_power: 1.0
+max_power: 0.5
 shutdown_speed: 0.0
 kick_start_time: 5.0
 heater: heater_bed
@@ -375,7 +396,7 @@ fan_speed: 1.0
 [heater_fan nevermore_fan]
 #  nevermore fan in fan3 connector
 pin: PB2
-max_power: 1.0
+max_power: 0.8
 shutdown_speed: 0.0
 kick_start_time: 5.0
 heater: heater_bed